manualshive.com logo in svg

Cisco ASR 9000 Series, Command Reference Manual

The Cisco ASR 9000 Series is a cutting-edge networking solution, offering unmatched performance and reliability. To streamline the installation process, it comes with a comprehensive Installation Manual available for free download from our website, empowering users with step-by-step instructions to maximize the potential of this exceptional product.

Share
Download
background image

peer ipv4 address

To configure the IPv4 address for a Session State Redundancy Protocol (SSRP) peer, use the

peer ipv4

address

command in SSRP configuration mode. To remove the address, use the no form of this command.

peer ipv4 address ip-address

no peer ipv4 address ip-address

Syntax Description

IP address of the peer interface whose states will be replicated by SSRP.

ip-address

Command Default

No default behavior or values

Command Modes

SSRP configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

Task ID

Operations

Task ID

read, write

ppp

Examples

The following example shows how to configure the IPv4 address for a Session State Redundancy Protocol
(SSRP) peer:

RP/0/RSP0/CPU0:router#

config

RP/0/RSP0/CPU0:router(config)#

ssrp profile Profile_1

RP/0/RSP0/CPU0:router(config-ssrp)#

peer ipv4 address 10.10.10.10

Related Commands

Description

Command

Configures a SSRP profile and enters the SSRP configuration
mode.

ssrp profile, on page 774

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x    

719

PPP Commands onthe Cisco ASR 9000 Series Router

peer ipv4 address

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Yeastar Technology TA3210 User Manual preview
TA3210
Brand: Yeastar Technology Pages: 66
Moxa Technologies MGate MB3480 Quick Installation Manual preview
MGate MB3480
Brand: Moxa Technologies Pages: 6
Esse-ti GSM400 User Manual preview
GSM400
Brand: Esse-ti Pages: 56
Garmin GHP Reactor Steer-by-Wire Volvo Quick Start Manual preview
GHP Reactor Steer-by-Wire Volvo
Brand: Garmin Pages: 6
M-system R7G-SC-SHL Instruction Manual preview
R7G-SC-SHL
Brand: M-system Pages: 7
BEC Ultimum 8900AX Quick Start Manual preview
Ultimum 8900AX
Brand: BEC Pages: 14
Tadiran Telecom aeonix TGW4 User Manual preview
aeonix TGW4
Brand: Tadiran Telecom Pages: 141
Planet VIP-2100 Specification Sheet preview
VIP-2100
Brand: Planet Pages: 140
Plugwise Adam Installation Manual preview
Adam
Brand: Plugwise Pages: 28
SmartRG SR360n User Manual preview
SR360n
Brand: SmartRG Pages: 122
Dynamix 2FXS/2FXO-B User Manual preview
2FXS/2FXO-B
Brand: Dynamix Pages: 122
More NF18MESH Quick Start Manual preview
NF18MESH
Brand: More Pages: 24
tilgin HG350 Series Quick Manual preview
HG350 Series
Brand: tilgin Pages: 20
tilgin HG321 Quick Manual preview
HG321
Brand: tilgin Pages: 20
tilgin HG2700 Series Quick Manual preview
HG2700 Series
Brand: tilgin Pages: 20
tilgin HG2300 series Quick Manual preview
HG2300 series
Brand: tilgin Pages: 28
Tema Telecomunicazioni DIAL-112 Technical Installation Manual preview
DIAL-112
Brand: Tema Telecomunicazioni Pages: 35
Planet Networking & Communication MH-5001 User Manual preview
MH-5001
Brand: Planet Networking & Communication Pages: 235

Brands by name

Popular brands

Load more brands