Cisco ASR 9000 Series Command Reference Manual Download

Page: 742 / 1138

RP/0/RSP0/CPU0:router(config-if)#

encapsulation ppp

RP/0/RSP0/CPU0:router(config-if)#

ppp authentication chap MIS-access

Related Commands

Description

Command

Specifies one or more AAA authentication methods
for use on serial interfaces running PPP.

aaa authentication ppp

Sets the encapsulation method used by the interface.

encapsulation

Configures a new user with a username, establishes
a password, and grants permissions for the user.

username

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

722

PPP Commands onthe Cisco ASR 9000 Series Router

ppp authentication

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands