Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 769 / 1138

background image

RP/0/RSP0/CPU0:router(config-if)#

ppp pap refuse

Related Commands

Description

Command

Specifies one or more authentication, authorization,
and accounting (AAA) methods for use on serial
interfaces running PPP.

aaa authentication ppp

Enables CHAP, MS-CHAP, or PAP, and specifies
the order in which CHAP, MS-CHAP, and PAP
authentication is selected on the interface.

ppp authentication , on page 720

Configures a PPP interface not to reset itself
immediately after an authentication failure but instead
to allow a specified number of authentication retries.

ppp max-bad-auth , on page 730

Enables remote PAP support for an interface, and
includes the

sent-username

and

password

commands

in the PAP authentication request packet to the peer.

ppp pap sent-username password, on page 750

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

749

PPP Commands onthe Cisco ASR 9000 Series Router

ppp pap refuse

«
...
767
768
769
770
771
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: SIGNAL FIRE Pages: 33

Brand: Extron electronics Pages: 23

Brand: B&B Pages: 2

Brand: Doepke Pages: 44

Brand: B+B Pages: 25

Brand: Nokia Pages: 107

Brand: QNAP Pages: 168

Brand: Fanvil Pages: 41

Brand: Fanvil Pages: 54

Brand: VOPtel Pages: 49

Brand: GRASS VALLEY Pages: 47

Brand: Bpt Pages: 25

Fieldgate SFG500

Brand: Endress+Hauser Pages: 52

Brand: Technicolor Pages: 103

Brand: Eaton Pages: 7

Brand: Telstra Pages: 34

Brand: MiSensors Pages: 22

Brand: Fanstel Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands