Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 772 / 1138

background image

ppp timeout authentication

To set PPP authentication timeout parameters, use the

ppp timeout authentication

command in interface

configuration mode. To reset the default value, use the

no

form of this command.

ppp timeout authentication seconds

no ppp timeout authentication

Syntax Description

Maximum time, in seconds, to wait for a response to an authentication packet. Range
is from 3 to 30 seconds. Default is 10 seconds.

seconds

Command Default

seconds

: 10

Command Modes

Interface configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

The default authentication time is 10 seconds, which should allow time for a remote router to authenticate
and authorize the connection and provide a response. However, it is also possible that it will take much less
time than 10 seconds. In such cases, use the

ppp timeout authentication

command to lower the timeout

period to improve connection times in the event that an authentication response is lost.

The timeout affects connection times only if packets are lost.

Note

Although lowering the authentication timeout is beneficial if packets are lost, sending authentication
requests faster than the peer can handle them results in churn and a slower connection time.

Note

Task ID

Operations

Task ID

read, write

ppp

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

752

PPP Commands onthe Cisco ASR 9000 Series Router

ppp timeout authentication

«
...
770
771
772
773
774
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: ICP DAS USA Pages: 7

Brand: ICP DAS USA Pages: 4

Brand: Nortel Pages: 111

Brand: NeoGate Pages: 41

Brand: Ingics Pages: 12

PVSG-IQAN-C2E1M2W1U1

Brand: Parker Pages: 70

Brand: CALEFFI Pages: 20

Brand: TP-Link Pages: 63

Link Gate GSM ISDN

Brand: Linkcom Pages: 22

Brand: DatoHome Pages: 6

Brand: Planet Networking & Communication Pages: 38

VGW 20FS Series

Brand: Planet Networking & Communication Pages: 84

Brand: Yeastar Technology Pages: 62

SenzaGate SG151lite

Brand: E-Senza Pages: 28

Brand: 2N Pages: 109

Brand: 2N Pages: 135

Brand: 2N Pages: 143

EAC Mini IL20EAC-N

Brand: Winmate Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands