Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 78 / 1138

background image

Table 2: show controllers dwdm Command Output Field Descriptions

Description

Field

Number of alarm indication signal (AIS) alarms. AIS
is a signal sent downstream as an indication that an
upstream defect has been detected.

AIS

Lists the alarms that are enabled for reporting.

Alarm reporting enabled for

Alarms indicated to be reported by the user.

Asserted Alarms

Number of backward defect indication (BDI) alarms.
The BDI is a single bit that conveys information
regarding signal failure in the upstream direction.

BDI

Values of the configured bit error rate thresholds.

BER thresholds

Number of bit interleaved parity alarms. The BIP is
comprised of one byte and is used for error detection.
It is computed over the entire optical channel payload
unit (OPU).

BIP

Status of the controller.

Controller State

Alarms detected by the hardware.

Detected Alarms

Corrected code words. This is the number of words
corrected by the FEC and is displayed as a per second
rate.

EC

Indicates the forward error correction (FEC) mode
for the controller. This can be Disabled, Enhanced
FEC G.975.1 1.4, or Standard FEC (Default).

FEC Mode

Number of incoming alignment errors (IAE).

IAE

Number of upstream connection locked alarms. LCK
is a signal sent downstream as an indication that
upstream the connection is locked, and no signal is
passed through.

LCK

Number of OTU loss of frame (LOF) alarms.

LOF

Number of OTU loss of multiframe (LOM) alarms.

LOM

Loopback status. Indicates whether or not loopback
is enabled and the type of loopback enabled.

Loopback

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

58

Dense Wavelength Division Multiplexing Commands on the Cisco ASR 9000 Series Router

show controller dwdm

«
...
76
77
78
79
80
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: 2N Pages: 2

Brand: KE2 Pages: 16

Brand: 2Wire Pages: 14

Brand: T-VIPS Pages: 200

Ability Cassia X2000

Brand: ABB Pages: 29

Brand: TENETICS, LLC Pages: 12

Brand: Efento Pages: 14

Brand: Zoom Pages: 54

Brand: Zoom Pages: 87

Brand: Zhone Pages: 151

TOOLBOX-ETH-GPRS

Brand: Ewattch Pages: 14

Brand: Abus Pages: 30

Brand: BossPac Pages: 27

Brand: Primus Pages: 2

Brand: Riello UPS Pages: 14

Brand: FarSite Communications Pages: 2

Brand: Deco Pages: 22

Brand: ICPDAS Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands