Cisco ASR 9000 Series Command Reference Manual Download

Page: 790 / 1138

Examples

This example shows how to display the number of sessions in each ICSSO state for each session layer.

RP/0/RSP0/CPU0:router#

show ppp sso summary location 0/3/cpu0

Not-Ready

: The session is not yet ready to run as Active or Standby

Stby-UnNegd

: In Standby mode, no replication state received yet

Act-Down

: In Active mode, lower layer not yet up

Deactivating : Session was Active, now going Standby
Act-UnNegd

: In Active mode, not fully negotiated yet

Stby-Negd

: In Standby mode, replication state received and pre-programmed

Activating

: Session was Standby and pre-programmed, now going Active

Act-Negd

: In Active mode, fully negotiated and up

: This layer not running

Not-

Stby-

Act- Deactiv- Act-

Stby-

Activ- Act

Layer

| Total

Ready

UnNegd Down

ating

UnNegd Negd

ating

Negd

-------------+------- ------ ------ ------ ------ ------ ------ ------ -----
LCP

of-us-auth

of-peer-auth |

IPCP

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

770

PPP Commands onthe Cisco ASR 9000 Series Router

show ppp sso summary

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands