Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 833 / 1138

background image

Operations

Task ID

read

cisco-support

Examples

The following example shows how to display IPv4, Real Time Protocol (RTP), User Datatgram Protocol
(UDP), and Non-Transmission Control Protocol (non-TCP) statistics about IP header compression (IPHC)
packets sent and received on an interface:

RP/0/RSP0/CPU0:router#

show iphc ipv4 rtp interface Serial 0/1/0/1/26:0

Thu Jan

8 20:28:47.569 UTC

RTP/UDP/IP header compression statistics:

Interface Serial0/1/0/1/26:0

Rcvd:

100 total, 93 compressed, 7 full header
0 dropped, 0 status msgs

Sent:

0 total, 0 compressed, 0 fullheader, 0 status msgs
0 bytes saved, 0 bytes sent
1.00 efficiency improvement factor

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

813

Serial Interface Commands on the Cisco ASR 9000 Series Router

show iphc ipv4 rtp

«
...
831
832
833
834
835
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Vega Pages: 39

Brand: National Instruments Pages: 14

MicroTrac Gateway

Brand: YASKAWA Pages: 33

NETcon D-G-64NE

Brand: ZIEHL-ABEGG Pages: 27

MultiVOIP MVPFX2-8

Brand: Multitech Pages: 8

Brand: Nokia Pages: 3

CC500 - VPN - Gateway

Brand: Nokia Pages: 11

Brand: Nokia Pages: 48

Brand: Nokia Pages: 58

Brand: Nokia Pages: 62

Brand: Nokia Pages: 72

Brand: Nokia Pages: 87

3TG-01275-AAAA-TCZZA

Brand: Nokia Pages: 96

Brand: Nokia Pages: 112

Brand: Samsung Pages: 20

Brand: Samsung Pages: 17

IPX-G5X0 series

Brand: Samsung Pages: 27

Brand: Samsung Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands