Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 907 / 1138

background image

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

Reporting an alarm means that the alarm can be logged to the console, but it is no guarantee that it is logged.
SONET alarm hierarchy rules dictate that only the most severe alarm of an alarm group is reported. Whether
an alarm is reported or not, you can check the current state of masked alarm, a problem indication that is a
candidate for an alarm, by displaying the

“

Masked Alarms

”

line in the

show controllers sonet

command

output.

For B1, the bit interleaved parity (BIP) error report is calculated by comparing the BIP-8 code with the BIP-8
code that is extracted from the B1 byte of the following frame. Differences indicate that section-level bit errors
have occurred.

For B2, the BIP error report is calculated by comparing the BIP-8/24 code with the BIP-8 code that is extracted
from the B2 byte of the following frame. Differences indicate that line-level bit errors have occurred.

Path AIS is sent by line terminating equipment to alert the downstream path terminating equipment (PTE)
that it has detected a defect on its incoming line signal.

Path loss of pointer (LOP) is reported as a result of an invalid pointer (H1, H2) or an excess number of new
data flag enabled indications.

SLOF is detected when an error-framing defect on the incoming SONET signal persists for 3 microseconds.

SLOS is detected when an all-zeros pattern on the incoming SONET signal is observed. This defect might
also be reported if the received signal level drops below the specified threshold.

To determine the alarms that are reported on the controller, use the

show controllers sonet

command.

Task ID

Operations

Task ID

read, write

sonet-sdh

Examples

The following example shows how to enable the reporting of line AIS alarms on the path controller:

RP/0/RSP0/CPU0:router(config)#

controller sonet 0/1/0/1

RP/0/RSP0/CPU0:router(config-sonet)#

report lais

Related Commands

Description

Command

Displays information about the operational status of SONET
layers.

show controllers sonet, on page 906

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

887

SONET Controller Commands on the Cisco ASR 9000 Series Router

report (SONET)

«
...
905
906
907
908
909
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Voice Gateway H3C VG 10-10

Brand: H3C Pages: 31

SR6602-I AI Series

Brand: H3C Pages: 80

SR6602-I AI Series

Brand: H3C Pages: 33

SecPath M9000 Series

Brand: H3C Pages: 4

SecPath M9000 Series

Brand: H3C Pages: 15

MSR3610-I Series

Brand: H3C Pages: 5

SecPath M9000 Series

Brand: H3C Pages: 57

WAGO 750-8212/000-100

Brand: Viessmann Pages: 36

460PBSDFM-N70PB

Brand: RTA Pages: 73

Brand: D2D Pages: 37

P-661H-D Series

Brand: ZyXEL Communications Pages: 113

CONTROLS Series

Brand: Condair Pages: 16

Brand: Fanvil Pages: 71

Brand: ABB Pages: 45

Brand: ABB Pages: 108

Brand: Bticino Pages: 4

Brand: Innoband Pages: 87

NetLinx NXB-CCG-K

Brand: AMX Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands