Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 909 / 1138

background image

candidate for an alarm, by inspecting the

“

Masked Alarms

”

line displayed in the

show controllers sonet

command output.

For B3, the bit interleaved parity (BIP) error report is calculated by comparing the BIP-8 code with the BIP-8
code that is extracted from the B3 byte of the following frame. Differences indicate that path-level bit errors
have occurred.

Path AIS is sent by line-terminating equipment to alert the downstream path-terminating equipment (PTE)
that it has detected a defect on its incoming line signal.

Path LOP is reported as a result of an invalid pointer (H1, H2) or an excess number of new data flag enabled
indications.

To determine the alarms that are reported on the controller, use the

show controllers sonet

command.

All report commands accept the default option. The default reporting values are determined based upon the
SONET standards specifications and are clearly identified in the corresponding command

’

s help string.

The reporting of B3 BER TCA errors and path LOP errors is enabled by default.

Note

Task ID

Operations

Task ID

read, write

sonet-sdh

Examples

In the following example, reporting of path PAIS alarms is enabled:

RP/0/RSP0/CPU0:router(config)#

controller sonet 0/2/0/2

RP/0/RSP0/CPU0:router(config-sonet)#

path

RP/0/RSP0/CPU0:router(config-sonet-path)#

report pais

Related Commands

Description

Command

Displays information about the operational status of SONET
layers.

show controllers sonet, on page 906

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

889

SONET Controller Commands on the Cisco ASR 9000 Series Router

report (SONET path)

«
...
907
908
909
910
911
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Advantech Pages: 82

IGW1111-3IN1-DB

Brand: 3onedata Pages: 3

Brand: AXIOMTEK Pages: 57

Brand: DoorKing Pages: 72

Brand: Ubee Pages: 103

Brand: Kaon Pages: 5

Brand: Gardena Pages: 29

Brand: gefran Pages: 2

Brand: Advantech Pages: 42

Brand: Raisecom Pages: 16

Brand: Gigalink Pages: 45

Brand: Zte Pages: 2

Brand: CalAmp Pages: 28

Brand: Zenner Pages: 8

Brand: Alliant Networks Pages: 83

Brand: Omnitracs Pages: 4

Brand: D-Link Pages: 71

Brand: Hach Pages: 428

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands