Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 938 / 1138

background image

signalling

To configure the K1K2 overhead byte signaling protocol used for automatic protection switching (APS), use
the

signalling

command in APS group configuration mode. To reset APS signaling to the default, use the

no

form of this command.

signalling

{

sonet| sdh

}

no signalling

{

sonet| sdh

}

Syntax Description

Sets signaling to SONET.

sonet

Sets signaling to Synchronous Digital Hierarchy (SDH).

sdh

Command Default

SONET signaling is set by default.

Command Modes

APS group configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

The

sdh

keyword was supported.

Release 4.0.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

By default, APS uses the signaling mode matching the framing mode. The

signalling

command may be

required, depending upon the transport equipment capabilities, only on

“

transition

”

links interconnecting

SONET and SDH networks.

In a multirouter APS topology, the

signalling

command is allowed only on the protect router.

Examples

The following example shows how to reset the signaling protocol from the default SONET value to SDH:

RP/0/RSP0/CPU0:router(config)#

aps group 1

RP/0/RSP0/CPU0:router(config-aps)#

signalling sdh

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

918

SONET Controller Commands on the Cisco ASR 9000 Series Router

signalling

«
...
936
937
938
939
940
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: ZIEHL-ABEGG Pages: 23

pathport quattro

Brand: pathway Pages: 14

Brand: HW Group Pages: 19

NetPerformer SDM-9220 Series

Brand: Memotec Pages: 146

Brand: Comtrend Corporation Pages: 84

M2M CONTROL CX530

Brand: Infranet Technologies Pages: 36

Brand: Seneca Pages: 4

Brand: ICP DAS USA Pages: 122

Harmony Platinum 6005A

Brand: Smartenit Pages: 2

Brand: SICK Pages: 60

PROFIBUS DP GATEWAY

Brand: Omron Pages: 95

Brand: Fanvil Pages: 5

Brand: Planet Pages: 2

Brand: Planet Networking & Communication Pages: 38

VGW 20FS Series

Brand: Planet Networking & Communication Pages: 84

Gateway 2070 Series

Brand: 2Wire Pages: 25

Brand: Vantron Pages: 29

PREMIERWAVE XC HSPA+

Brand: Lantronix Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands