Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 959 / 1138

background image

◦

slot

: Physical slot number of the line card.

◦

module

: Module number. A physical layer interface module (PLIM) is always 0.

◦

port

: Physical port number of the interface.

•

If specifying a virtual interface, the number range varies, depending on interface type.

Before you can start a BERT on an E1 controller or channel group, you must configure a BERT pattern
using the

bert pattern

command. If desired, you can also adjust the default setting (1 minute) of the BERT

interval using the

bert interval

command. Both of these commands are available in E1 configuration

mode and channel group configuration mode.

Note

To view the BERT results, use the

show controllers e1

command in EXEC mode. The BERT results include

the following information:

•

Type of test pattern selected

•

Status of the test

•

Interval selected

•

Time remaining on the BERT

•

Total bit errors

•

Total bits received

BERT is data intrusive. Regular data cannot flow on a line while the test is in progress. The line is put in an
alarm state when a BERT is in progress and restored to a normal state after a BERT has been terminated.

Task ID

Operations

Task ID

read, write

sonet-sdh

Examples

The following example shows how to start and stop a BERT on an E1 controller:

RP/0/RSP0/CPU0:router#

bert e1 0/3/0/0 start

RP/0/RSP0/CPU0:router#

bert e1 0/3/0/0 stop

The following example shows how to inject errors into the BERT stream on an E1 controller:

RP/0/RSP0/CPU0:router#

bert e1 0/3/0/0 error

Related Commands

Description

Command

Specifies the duration of a bit error rate test (BERT) pattern on a
T3/E3 or T1/E1 line.

bert interval, on page 945

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

939

T3, E3, T1, E1 Controller Commands on the Cisco ASR 9000 Series Router

bert e1

«
...
957
958
959
960
961
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: JBM electronics Pages: 20

Brand: 2N Pages: 2

Brand: 2N Pages: 2

Brand: 2N Pages: 4

Brand: Epygi Pages: 87

Brand: Nitgen Pages: 36

AirLink PinPoint X

Brand: Sierra Wireless Pages: 62

Brand: Siemens Pages: 14

RUGGEDCOM WIN5137-V

Brand: Siemens Pages: 34

RUGGEDCOM WIN5151

Brand: Siemens Pages: 46

Gigaset SX686 WiMAX

Brand: Siemens Pages: 40

RUGGEDCOM WIN5151

Brand: Siemens Pages: 108

Brand: Siemens Pages: 296

Internet Security Gateway ZyWALL 100

Brand: ZyXEL Communications Pages: 708

ADSL2+ Ethernet/USB Gateway 660RU-Tx Series

Brand: ZyXEL Communications Pages: 286

Brand: BellEquip Pages: 20

Brand: X2E Pages: 22

Brand: Pace Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands