Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 146 / 1138

background image

speed (Fast Ethernet)

To configure the speed for a Fast Ethernet interface, enter the

speed

command in interface configuration

mode. To return the system to autonegotiate speed, use the

no

form of this command.

speed

{

10| 100| 1000

}

no speed

Syntax Description

Configures the interface to transmit at 10 Mbps.

10

Configures the interface to transmit at 100 Mbps.

100

Configures the interface to transmit at 1000 Mbps (1 Gbps).

1000

Command Default

If autonegotiation is enabled on an interface, the default speed is negotiated.

If autonegotiation is disabled on an interface, the default speed is the maximum speed allowed on the interface.

Command Modes

Interface configuration

Command History

Modification

Release

This command was introduced.

Release 4.2.3

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

The

speed

command is available on Management Ethernet interfaces and Fast Ethernet interfaces only.

Note

Keep in mind that both ends of a link must have the same interface speed. A manually configured interface
speed overides any autonegotiated speed, which can prevent a link from coming up if the configured
interface speed at one end of a link is different from the interface speed on the other end.

Note

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

126

Ethernet Interface Commands on the Cisco ASR 9000 Series Router

speed (Fast Ethernet)

«
...
144
145
146
147
148
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Eaton Pages: 2

Mediant 1000 MSBG

Brand: AudioCodes Pages: 160

Brand: THOMSON Pages: 90

Brand: FACTBIRD Pages: 2

Brand: Pathway connectivity solutions Pages: 14

Brand: Pace Pages: 19

NIOT-E-TPI51-EN-RE

Brand: hilscher Pages: 258

Brand: ZyXEL Communications Pages: 2

Brand: Nitgen Pages: 36

Brand: Sagem Pages: 27

Brand: NetPurifier Pages: 49

Brand: Cisco Pages: 76

Brand: MOKO Pages: 34

RouteFinder RF550VPN

Brand: Multi-Tech Pages: 76

Brand: Kiloview Pages: 11

Brand: ICP DAS USA Pages: 24

Brand: Dormakaba Pages: 8

Brand: Technicolor Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands