Cisco ASR 9000 Series Command Reference Manual Download

Page: 204 / 1138

clear ethernet sla statistics profile

To delete the contents of buckets containing SLA statistics collected by probes for a profile, use the

clear

ethernet sla statistics profile

command in EXEC mode.

clear ethernet sla statistics

[

current| history

]

profile

{

all

profile-name

} [

interface type interface-path-id

domain all

interface type interface-path-id domain domain-name target

{

all

mac-address H.H.H

mep-id

interface all domain domain-name

]

Syntax Description

(Optional) Clears statistics for all buckets currently being filled.

current

(Optional) Clears statistics for all full buckets.

history

Clears statistics for the specified profile name.

profile-name

Clears statistics for all profiles.

all

(Optional) Clears statistics for the specified interface type. For more
information, use the question mark (

) online help function.

interface type

Physical interface or virtual interface.

Use the

show interfaces

command to see a list of all interfaces

currently configured on the router.

Note

For more information about the syntax for the router, use the question mark
(

) online help function.

interface-path-id

Clears statistics for on-demand operations for all domains.

domain all

Clears statistics for on-demand operations for the specified domain.

domain domain-name

Clears statistics for on-demand operations targeted to all MEPs for the
specified interface domain.

target all

Clears statistics for on-demand operations targeted to the specified MAC
address.

target mac-address H.H.H

Clears statistcs for on-demand operations targeted to the specified MEP ID.

target mep-id id

(Optional) Clears statistics for on-demand operations on all interfaces.

interface all

Command Default

When

current

history

are not used, all buckets in the profile (current, old, new, half empty, and full) are

cleared. This is equivalent to restarting the operation.

Command Modes

EXEC (#)

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

184

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

clear ethernet sla statistics profile

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands