Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 233 / 1138

background image

ethernet oam loopback

To start or stop a loopback at the remote end of an Ethernet OAM interface, use the

ethernet oam loopback

command in EXEC mode.

ethernet oam loopback

{

enable| disable

}

type interface-path-id

Syntax Description

Starts a loopback at the remote end.

enable

Stops the loopback at the remote end.

disable

Interface type. For more information, use the question mark (

?

) online help

function.

type

Physical interface or virtual interface.

Use the

show interfaces

command to see a list of all interfaces currently

configured on the router.

Note

For more information about the syntax for the router, use the question mark (

?

)

online help function.

interface-path-id

Command Default

Loopback is not enabled.

Command Modes

EXEC mode

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Usage Guidelines

This command puts the remote peer device into loopback mode. This means that all traffic sent to the peer is
looped back, which means that it is sent back from the peer and received by the router. All traffic received
from the peer device is discarded.

This command returns when the OAM client receives confirmation from the remote end that the remote
loopback has been enabled or disabled. If no response or a failure response is received, an error is returned.

Task ID

Operations

Task ID

execute

ethernet-services

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

213

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

ethernet oam loopback

«
...
231
232
233
234
235
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Yeastar Technology Pages: 17

Brand: Gallagher Pages: 2

Brand: HALNy Pages: 8

Brand: AudioCodes Pages: 5

Brand: Grandstream Networks Pages: 32

Brand: Ascent Communication Technology Pages: 114

Brand: OPW Pages: 13

Brand: Planet Pages: 8

Brand: Planet Pages: 16

Brand: Planet Pages: 16

Brand: Planet Pages: 131

Brand: Luminext Pages: 8

Brand: R9 Technology Pages: 5

Brand: TVILIGHT Pages: 15

Brand: Sollae Systems Pages: 29

Brand: SINBON Pages: 21

Brand: Cooper Bussmann Pages: 115

Touchstone DG1680

Brand: Arris Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands