Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 422 / 1138

background image

statistics measure

To enable the collection of Ethernet Service Level Agreement (SLA) statistics, and enter the SLA profile
statistics configuration mode, use the

statistics measure

command in SLA profile configuration mode. To

disable statistics collection, use the

no

form of this command.

statistics measure

{

one-way-delay-ds| one-way-delay-sd| one-way-jitter-ds| one-way-jitter-sd|

round-trip-delay| round-trip-jitter| one-way-loss-sd| one-way-loss-ds

}

no statistics measure

{

one-way-delay-ds| one-way-delay-sd| one-way-jitter-ds| one-way-jitter-sd|

round-trip-delay| round-trip-jitter| one-way-loss-sd| one-way-loss-ds

}

Syntax Description

(CFM delay measurement profile type only) Enables the collection of statistics
that measure delay in one direction, from destination to source.

one-way-delay-ds

(CFM delay measurement profile type only) Enables the collection of statistics
that measure delay in one direction, from source to destination.

one-way-delay-sd

(CFM delay measurement profile type only) Enables the collection of statistics
that measure delay variance in one direction, from destination to source.

one-way-jitter-ds

(CFM delay measurement profile type only) Enables the collection of statistics
that measure delay variance in one direction, from source to destination.

one-way-jitter-sd

(CFM delay measurement and CFM loopback profile types only) Enables the
collection of statistics that measure the delay in the round trip of a packet.

round-trip-delay

(CFM delay measurement and CFM loopback profile types only) Enables the
collection of statistics that measure the amount of delay variance in the round
trip of a packet.

round-trip-jitter

(CFM loss measurement profile type only) Enables the collection of statistics
that measure the synthetic loss in one direction, from source to destination.

one-way-loss-sd

(CFM loss measurement profile type only) Enables the collection of statistics
that measure the synthetic loss in one direction, from destination to source.

one-way-loss-ds

Command Default

No statistics are collected

Command Modes

SLA profile configuration (config-sla-prof)

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

402

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

statistics measure

«
...
420
421
422
423
424
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Luminext Pages: 8

Brand: Seneca Pages: 22

Brand: FACTBIRD Pages: 2

Brand: Quadro Pages: 54

Brand: McQuay Pages: 52

Brand: Grandstream Networks Pages: 54

AirLink PinPoint X

Brand: Sierra Wireless Pages: 62

Smart Command 410100

Brand: Caroma Pages: 2

Brand: Huawei Pages: 28

Brand: Nortel Pages: 134

Remote Office 9150

Brand: Nortel Pages: 570

Brand: Mercury Pages: 5

Brand: tilgin Pages: 20

Brand: tilgin Pages: 20

Brand: tilgin Pages: 20

Brand: tilgin Pages: 28

WiSenMeshWAN 6003

Brand: Wisen Pages: 11

Brand: Elesign Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands