Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 611 / 1138

background image

isolation recovery-delay

To specify a delay before clearing the isolation condition after recovery from failure, use the

isolation

recovery-delay

command in the redundancy group ICCP configuration mode. To return to the default value,

use the

no

form of this command.

isolation recovery-delay seconds

no isolation recovery-delay seconds

Syntax Description

Recovery delay in seconds.

seconds

Command Default

By default, the delay is set to 180 seconds.

Command Modes

Redundancy group ICCP configuration

Command History

Modification

Release

This command was introduced.

Release 4.0.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

Examples

This example shows how to configure ICCP parameters:

RP/0/RSP0/CPU0:router#

configure

RP/0/RSP0/CPU0:router(config)#

redundancy iccp group 10

RP/0/RSP0/CPU0:router(config-redundancy-iccp-group)#

isolation recovery-delay 35

RP/0/RSP0/CPU0:router(config-redundancy-iccp-group)#

Task ID

Operations

Task ID

read, write

config-services

Related Commands

Description

Command

Configures Inter Chassis Communication Protocol (ICCP)
parameters.

redundancy iccp group, on page 617

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

591

Link Bundling Commands on the Cisco ASR 9000 Series Router

isolation recovery-delay

«
...
609
610
611
612
613
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: ICP DAS USA Pages: 7

Brand: ICP DAS USA Pages: 4

Brand: Deb Pages: 4

Brand: Zennio Pages: 38

SBG3500-N Series

Brand: ZyXEL Communications Pages: 10

Network Device P-2302

Brand: ZyXEL Communications Pages: 359

Brand: Ascent Communication Technology Pages: 114

Brand: MediaAccess Pages: 68

TOPEX MobiLink IP

Brand: Topex Pages: 80

Brand: digitalSTROM Pages: 27

Brand: Carotron Pages: 20

Brand: Funkwerk Pages: 594

Brand: Dynamix Pages: 122

Brand: BossPac Pages: 26

Brand: QUANTUM X Pages: 56

Brand: Exegin Pages: 84

Brand: Gempro Technology Pages: 21

DataRoute voice

Brand: Telecom FM Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands