manualshive.com logo in svg

Cisco ASR 9000 Series, Command Reference Manual

The Cisco ASR 9000 Series is a cutting-edge networking solution, offering unmatched performance and reliability. To streamline the installation process, it comes with a comprehensive Installation Manual available for free download from our website, empowering users with step-by-step instructions to maximize the potential of this exceptional product.

Share
Download
background image

lacp non-revertive

To configure the currently active but lower priority port to remain active port even after a higher priority port
is capable of being operational, use the

lacp non-revertive

command in the bundle interface configuration

mode. To revert to the default configuration, use the

no

form of this command.

lacp non-revertive

no lacp non-revertive

This command has no keywords or arguments.

Command Default

A higher priority port would become the active port after it becomes operational again.

Command Modes

Bundle interface configuration mode

Command History

Modification

Release

This command was introduced.

Release 5.3.2

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

Task ID

Operation

Task ID

read, write

Examples

The following example shows how to configure the non-revertive behaviour on an LACP bundle interface.

RP/0/RSP0/CPU0:router#

configure

RP/0/RSP0/CPU0:router(config)#

interface bundle-ether 1

RP/0/RSP0/CPU0:router(config-if)#

lacp non-revertive

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

598

Link Bundling Commands on the Cisco ASR 9000 Series Router

lacp non-revertive

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Zero 88 Betapack 4 Manual preview
Betapack 4
Brand: Zero 88 Pages: 16
Multitech MultiConnect Conduit Getting Started Manual preview
MultiConnect Conduit
Brand: Multitech Pages: 37
Moxa Technologies MGate MB3480 Quick Installation Manual preview
MGate MB3480
Brand: Moxa Technologies Pages: 6
Spectrum Brands KEVO Gateway Setup preview
KEVO Gateway
Brand: Spectrum Brands Pages: 2
ZyXEL Communications P-873HNU(B)-51B Quick Start Manual preview
P-873HNU(B)-51B
Brand: ZyXEL Communications Pages: 12
Veratron B00042201 Operating Instructions Manual preview
B00042201
Brand: Veratron Pages: 79
HMS AB7612 User Manual preview
AB7612
Brand: HMS Pages: 74
Novell ACCESS MANAGER 3.1 SP1 - ADMINISTRATION Installation Manual preview
ACCESS MANAGER 3.1 SP1 - ADMINISTRATION
Brand: Novell Pages: 42
Novatel SA2100 User Manual preview
SA2100
Brand: Novatel Pages: 88
Hybertone HT-322 User Manual preview
HT-322
Brand: Hybertone Pages: 33
Grandstream Networks GXW-4104 Technical Specifications preview
GXW-4104
Brand: Grandstream Networks Pages: 2
Alcatel-Lucent OmniAccess 8550 Installation Manual preview
OmniAccess 8550
Brand: Alcatel-Lucent Pages: 98
ZyXEL Communications XMG3927-B 0A Series Quick Start Manual preview
XMG3927-B 0A Series
Brand: ZyXEL Communications Pages: 2
ZyXEL Communications AMG1202-T series User Manual preview
AMG1202-T series
Brand: ZyXEL Communications Pages: 320
SmartRG SR516ac User Manual preview
SR516ac
Brand: SmartRG Pages: 158
AirLive IAS-2000 V2 User Manual preview
IAS-2000 V2
Brand: AirLive Pages: 163
Rosemount 1420 Quick Start Manual preview
1420
Brand: Rosemount Pages: 28
ViewSonic WPG-300 User Manual preview
WPG-300
Brand: ViewSonic Pages: 68

Brands by name

Popular brands

Load more brands