Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 628 / 1138

background image

mlacp connect

To specify configuration options for connecting to mLACP peers, use the

mlacp connect

command in the

redundancy ICCP group configuration mode. To disable this feature, use the

no

form of this command.

mlacp connect timeout seconds

no mlacp connect timeout seconds

Syntax Description

Specifies the time to wait before assuming mLACP peer is down.

timeout

Number of seconds to wait before assuming the mLACP peer is down.

seconds

Command Default

No default behavior or values

Command Modes

Redundancy ICCP group configuration

Command History

Modification

Release

This command was introduced.

Release 4.0.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

Task ID

Operations

Task ID

read, write

bundle

Examples

This example shows how to specify configuration options for connecting to mLACP peers:

RP/0/RSP0/CPU0:router#

configure

RP/0/RSP0/CPU0:router(config)#

redundancy iccp group 10

RP/0/RSP0/CPU0:router(config-redundancy-iccp-group)#

mlacp connect timeout 100

RP/0/RSP0/CPU0:router(config-redundancy-iccp-group)#

Related Commands

Configures ICCP parameters.

redundancy iccp group

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

608

Link Bundling Commands on the Cisco ASR 9000 Series Router

mlacp connect

«
...
626
627
628
629
630
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Icom Pages: 2

Brand: Icom Pages: 326

Brand: Xtrend Pages: 68

Brand: AudioCodes Pages: 5

Brand: SVS Pages: 4

Brand: B&B Pages: 2

KoolKey EKA 200

Brand: Danfoss Pages: 2

Brand: Gree Pages: 12

Brand: Samsung Pages: 20

Brand: Samsung Pages: 17

IPX-G5X0 series

Brand: Samsung Pages: 27

Brand: Samsung Pages: 27

Brand: Samsung Pages: 28

Brand: Samsung Pages: 64

Brand: Samsung Pages: 57

Brand: Samsung Pages: 67

Brand: Samsung Pages: 68

Brand: Samsung Pages: 200

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands