Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 635 / 1138

background image

mlacp system priority

To configure the LACP system priority to be used in the ICCP group, use the

mlacp system priority

command

in the redundancy ICCP group configuration mode. To return to the default value, use the

no

form of this

command.

mlacp system priority priority

no mlacp system priority priority

Syntax Description

Specifies the priority for the system.

Lower value indicates higher
priority.

Note

priority

Command Default

No default behavior or values

Command Modes

Redundancy ICCP group configuration

Command History

Modification

Release

This command was introduced.

Release 4.0.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

Task ID

Operations

Task ID

read, write

bundle

Examples

This example shows how to configure the LACP system priority to be used in the ICCP Group:

RP/0/RSP0/CPU0:router#

configure

RP/0/RSP0/CPU0:router(config)#

redundancy iccp group 10

RP/0/RSP0/CPU0:router(config-redundancy-iccp-group)#

mlacp system priority 10

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

615

Link Bundling Commands on the Cisco ASR 9000 Series Router

mlacp system priority

«
...
633
634
635
636
637
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Power Xpert Meter 2000

Brand: Eaton Pages: 71

Power Xpert Gateway 900

Brand: Eaton Pages: 25

SmartNode 10100 Series

Brand: Patton Pages: 12

FiberPlex FPX6000 Series

Brand: Patton Pages: 20

SmartNode 4970 Series

Brand: Patton Pages: 57

WILOW-IOT-GATEWAY-4G

Brand: BEANAIR Pages: 29

Zone Controller Pro ZCM-V2

Brand: Atlas Pages: 4

Brand: Vaisala Pages: 32

Brand: Vaillant Pages: 40

Brand: Peak Pages: 73

HomePortal 3700HGV

Brand: 2Wire Pages: 4

Brand: NavCom Technology Pages: 7

Brand: Fanstel Pages: 18

Brand: Vbox Communications Pages: 88

Brand: Tatung Pages: 7

SmartNode 4520 Series

Brand: Patton Pages: 12

Brand: Gingerway Pages: 8

Brand: Asus Pages: 227

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands