Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 759 / 1138

background image

ppp ms-chap password

To configure a common Microsoft Challenge Handshake Authentication (MS-CHAP) secret password, use
the

ppp ms-chap password

command in interface configuration mode. To disable the password, use the

no

form of this command.

ppp ms-chap password

[

clear| encrypted

]

password

no ppp ms-chap password

[

clear| encrypted

]

password

Syntax Description

(Optional) Specifies the cleartext encryption parameter for the password.

clear

(Optional) Indicates that the password is already encrypted.

encrypted

Cleartext or already-encrypted password.

password

Command Default

The password is disabled.

Command Modes

Interface configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

The

ppp ms-chap password

command is sent in CHAP responses and is used by the peer to authenticate the

local router. This does not affect local authentication of the peer. The

ppp ms-chap password

command is

useful for routers that do not support this command (such as routers running older software images).

The MS-CHAP secret password is used by the routers in response to challenges from an unknown peer.

Task ID

Operations

Task ID

read, write

ppp

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

739

PPP Commands onthe Cisco ASR 9000 Series Router

ppp ms-chap password

«
...
757
758
759
760
761
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Esse-ti Pages: 56

SmartNode 5540E Series

Brand: Patton Pages: 77

Brand: Ubiquiti Pages: 19

Brand: Nitgen Pages: 66

Brand: Stahl Pages: 64

VBG-PN-K20-DMD-EV

Brand: Pepperl+Fuchs Pages: 11

Brand: NKE Pages: 14

M2M CONTROL CX660

Brand: Infranet Technologies Pages: 44

Brand: D-Link Pages: 7

DPG-2000W - AirPlus G Wireless Presentation Gateway

Brand: D-Link Pages: 12

Brand: D-Link Pages: 37

DSA 5100 - Airspot - Gateway

Brand: D-Link Pages: 28

Brand: D-Link Pages: 12

Brand: D-Link Pages: 50

Brand: D-Link Pages: 67

Brand: D-Link Pages: 17

Brand: D-Link Pages: 13

Brand: D-Link Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands