Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 793 / 1138

background image

ssrp location

To specify the node on which to create a Session State Redundancy Protocol (SSRP) group and enter the
SSRP node configuration mode, use the

ssrp location

command in global configuration mode.

ssrp location node_id

Syntax Description

Specifies the full qualified path of a specific node in the format

rack

/

slot

/

module.

node_id

Command Default

No default behavior or values

Command Modes

Global configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

The location specifies the card on which an SSRP group is created.

Task ID

Operations

Task ID

read, write

ppp

Examples

This example shows how to create an SSRP group on a specified node for use by any interface on the card:

RP/0/RSP0/CPU0:router#

config

RP/0/RSP0/CPU0:router(config)#

ssrp location 0/1/cpu0

RP/0/RSP0/CPU0:router(config-ssrp-node)#

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

773

PPP Commands onthe Cisco ASR 9000 Series Router

ssrp location

«
...
791
792
793
794
795
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Panasonic Pages: 72

Brand: IAI Pages: 5

Brand: Ubee Pages: 99

Brand: Dragino Pages: 61

Brand: Sencore Pages: 37

WPC-832-2-Modbus-MQTT

Brand: KSH International Pages: 16

Brand: ANTIFERENCE Pages: 26

Brand: Huawei Pages: 92

Brand: Huawei Pages: 29

EchoLife HG8240

Brand: Huawei Pages: 358

Brand: Huawei Pages: 57

Brand: Huawei Pages: 42

EchoLife HG8045A

Brand: Huawei Pages: 42

Brand: Huawei Pages: 63

EchoLife HG552a

Brand: Huawei Pages: 37

Brand: Huawei Pages: 33

Brand: Huawei Pages: 27

Brand: Huawei Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands