Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 855 / 1138

background image

ais-shut (SONET)

To enable automatic insertion of a line alarm indication signal (LAIS) in the sent SONET signal whenever
the SONET port enters the administrative shutdown state, use the

ais-shut

command in SONET/SDH

configuration mode. To disable automatic insertion of a LAIS, use the

no

form of this command.

ais-shut

no ais-shut

Syntax Description

This command has no keywords or arguments.

Command Default

This command is disabled by default; no AIS is sent.

Command Modes

SONET configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

When the line is placed in administrative shutdown state, use the

ais-shut

command to send a signal to

downstream equipment that indicates that there is a problem with the line.

The

ais-shut

command is ignored if automatic protection switching (APS) is running for the corresponding

port, because the setting must be enabled for proper APS operation.

For SONET ports that do not have hardware support for LAIS insertion, the

ais-shut

command is disabled.

Task ID

Operations

Task ID

read, write

sonet-sdh

Examples

In the following example, the alarm indication is forced on the SONET OC-3 controller:

RP/0/RSP0/CPU0:router(config)#

controller sonet 0/1/0/0

RP/0/RSP0/CPU0:router(config-sonet)#

ais-shut

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

835

SONET Controller Commands on the Cisco ASR 9000 Series Router

ais-shut (SONET)

«
...
853
854
855
856
857
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

OA5305-13maw-EU

Brand: Alcatel Pages: 4

Brand: NetComm Pages: 16

Brand: ICP DAS USA Pages: 71

Brand: Pace Pages: 2

SBG3500-N Series

Brand: ZyXEL Communications Pages: 10

Brand: THOMSON Pages: 710

Brand: AudioCodes Pages: 70

Brand: Comtrend Corporation Pages: 84

Brand: YZ Systems Pages: 25

Brand: RTA Pages: 80

Brand: CHIYU Pages: 38

PowerConnect J-SRX240

Brand: Dell Pages: 160

PowerConnect J-SRX210

Brand: Dell Pages: 182

Dell Edge Gateway 3002

Brand: Dell Pages: 22

PowerConnect J-SRX100S

Brand: Dell Pages: 44

SonicWall SRA 1600

Brand: Dell Pages: 57

Brand: UNION Market Pages: 36

KONA ENTERPRISE T0007242

Brand: TEKTELIC Communications Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands