manualshive.com logo in svg

Cisco ASR 9000 Series, Command Reference Manual

The Cisco ASR 9000 Series is a cutting-edge networking solution, offering unmatched performance and reliability. To streamline the installation process, it comes with a comprehensive Installation Manual available for free download from our website, empowering users with step-by-step instructions to maximize the potential of this exceptional product.

Share
Download
background image

overhead (SONET path)

To set the SONET path overhead bytes in the frame header to a specific standards requirement or to ensure
interoperability with equipment from another vendor, use the

overhead

command in SONET/SDH path

configuration mode. To remove the setting of the SONET path overhead bytes from the configuration file
and restore the system to its default condition, use the

no

form of this command.

overhead

{

c2 byte-value

|

expected-trace LINEascii-text

|

j1 ascii-value

}

no overhead

{

c2 byte-value

|

expected-trace LINEascii-text

|

j1 ascii-value

}

Syntax Description

Specifies Synchronous Transport Signal (STS) synchronous payload envelope (SPE)
content (C2) byte. The transmitted

c2

value is automatically set to 0xCF for unscrambled

payload and 0x16 for scrambled payload. If c2 is configured to a user-specified value,
the user-specified value is always applied regardless of scrambling.

Replace the

byte-value

argument with the byte value to which the

c2

keyword should be

set. Range is from 0 to 255. Default value is 0.

c2 byte-value

Configures the SONET path trace (j1) buffer.

Replace the

ascii-value

argument with a text string that describes the SONET path trace

buffer. Default is a 64-byte path trace ASCII message, which includes default information
such as router name, (Layer 2

—

POS ) interface name, and IP address, if applicable.

j1 ascii-value

Configures the SONET/SDH path trace. The trace monitoring feature allows a node to
perform trace monitoring by using the SONET/SDH capabilities.

Replace the

LINE

with the expected trace message

Replace the

ascii-text

argument with a text string that describes the SONET path trace

buffer. Default is a 64-byte path trace ASCII message, which includes default information
such as router name, (Layer 2

—

POS ) interface name, and IP address, if applicable.

the LINE is the expected trace message which should match else ptim mismatch would
be reported

expected-trace
LINE ascii-text

Command Default

byte-value

: 0xCF

byte-value

: 0

Command Modes

SONET/SDH path configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

878

SONET Controller Commands on the Cisco ASR 9000 Series Router

overhead (SONET path)

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

RTA 460PSBM-N2EW Product User Manual preview
460PSBM-N2EW
Brand: RTA Pages: 81
Matrix Telecom SIMADO GFX44 Quick Start Manual preview
SIMADO GFX44
Brand: Matrix Telecom Pages: 32
NetComm Wireless NF18ACV Setup Manual preview
NF18ACV
Brand: NetComm Wireless Pages: 7
ZyXEL Communications HLA3105 User Manual preview
HLA3105
Brand: ZyXEL Communications Pages: 2
WirelessHART Fieldgate SWG70 Operating Instructions Manual preview
Fieldgate SWG70
Brand: WirelessHART Pages: 124
Asus Aaeon AIOT-QM User Manual preview
Aaeon AIOT-QM
Brand: Asus Pages: 39
Banner DX81H Network Manual preview
DX81H
Brand: Banner Pages: 110
Maxis TG784n User Manual preview
TG784n
Brand: Maxis Pages: 25
Innoband 6000-B1 User Manual preview
6000-B1
Brand: Innoband Pages: 87
Inteno DG200 Series User Manual preview
DG200 Series
Brand: Inteno Pages: 90
Allo.com Analog Gateway User Manual preview
Analog Gateway
Brand: Allo.com Pages: 62
Baxi Gateway 17 Installation Manual preview
Gateway 17
Brand: Baxi Pages: 10
Planet Networking & Communication MH-5001 User Manual preview
MH-5001
Brand: Planet Networking & Communication Pages: 235
Four-Faith F8926-GW Series User Manual preview
F8926-GW Series
Brand: Four-Faith Pages: 78
AudioCodes Mediant 2000 User Manual preview
Mediant 2000
Brand: AudioCodes Pages: 418
TECOM IG6600 Quick Installation Manual preview
IG6600
Brand: TECOM Pages: 5
MiSensors MNG-9-2A2V User Manual preview
MNG-9-2A2V
Brand: MiSensors Pages: 22
Kiwi TLG8411V1 User Manual preview
TLG8411V1
Brand: Kiwi Pages: 60

Brands by name

Popular brands

Load more brands