Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 910 / 1138

background image

revert

To enable automatic switchover from the protect interface to the working interface after the working interface
becomes available, use the

revert

command in APS configuration mode. To disable automatic switchover,

use the

no

form of this command.

revert minutes

no revert minutes

Syntax Description

Number of minutes until the circuit is switched back to the working interface after
the working interface is available.

minutes

Command Default

minutes

: 0

Automatic switchover is disabled.

Command Modes

APS group configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

Use the

revert

command to enable and disable revertive APS operation mode, if needed. The revertive APS

operation mode of the routers should be matched with the APS operation mode of the connected SONET
equipment. Use the

no

form of this command to disable automatic switchover.

The revertive APS operation mode is the recommended operation mode because it offers better traffic protection
during various possible software failures and upgrade or downgrade scenarios.

The

minutes

argument indicates how many minutes will elapse until automatic protection switching (APS)

decides to switch traffic back from protect to working after the condition that caused an automatic (Signal
Failed or Signal Degrade) switch to protect disappears. A value of 0 (default) disables APS revertive mode.

In a multirouter APS topology, the

revert

command is allowed only on the protect router.

Task ID

Operations

Task ID

read, write

sonet-sdh

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

890

SONET Controller Commands on the Cisco ASR 9000 Series Router

revert

«
...
908
909
910
911
912
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

SmartZone EPA126

Brand: Panduit Pages: 13

Brand: Dinstar Pages: 41

Brand: Foxconn Pages: 14

Brand: Synway Pages: 7

Brand: SenseNet Pages: 11

Brand: Z-Wave Pages: 68

Brand: NXP Semiconductors Pages: 2

MultiVOIP MVP130BG

Brand: Bogen Pages: 2

Brand: Samsung Pages: 20

Brand: Samsung Pages: 17

IPX-G5X0 series

Brand: Samsung Pages: 27

Brand: Samsung Pages: 27

Brand: Samsung Pages: 28

Brand: Samsung Pages: 64

Brand: Samsung Pages: 57

Brand: Samsung Pages: 67

Brand: Samsung Pages: 68

Brand: Samsung Pages: 200

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands