Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 977 / 1138

background image

channel-group

To configure a DS0 channel group and enter channel group configuration mode, use the

channel-group

command in T1 or E1 configuration mode. To unassign a channel group, use the

no

form of this command.

channel-group channel-group-number

no channel-group channel-group-number

Syntax Description

Channel group number. When a T1 controller is configured,
channel group numbers can be values from 0 to 23.

Note

channel-group-number

Command Default

No default behavior or values

Command Modes

T1 configuration

E1 configuration

Command History

Modification

Release

This command was introduced.

Release 3.9.0

Support for DS0 channel groups and E1 configuration was added.

Release 4.0.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

The

channel-group

command is available only on channelized SPAs.

Use the

channel-group

command in configurations in which the router must communicate with a T1 or an

E1 fractional data line. The channel group number may be arbitrarily assigned and must be unique for the
controller. An associated serial interface is created with each defined channel group.

Before the channel group configuration is valid, you must define the associated DS0 time slots using the

timeslots

command.

Use the

no channel group

command to delete a channel group.

Task ID

Operations

Task ID

read, write

sonet-sdh

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

957

T3, E3, T1, E1 Controller Commands on the Cisco ASR 9000 Series Router

channel-group

«
...
975
976
977
978
979
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Nmea Connect Plus

Brand: Calypso Pages: 21

Brand: Duemmegi Pages: 11

UNIGATE IC - Powerlink

Brand: DEUTSCHMANN AUTOMATION Pages: 50

INKNXMIT015C000

Brand: HMS Pages: 32

Brand: ZyXEL Communications Pages: 2

Brand: Stahl Pages: 64

Brand: Inteno Pages: 90

Brand: Helmholz Pages: 12

Brand: Helmholz Pages: 56

Brand: ETC Pages: 5

OmniAccess 8550

Brand: Alcatel-Lucent Pages: 98

Brand: Hitron Pages: 2

Brand: Schwaiger Pages: 24

Brand: TASHI Pages: 2

Brand: Planet Networking & Communication Pages: 12

Brand: Planet Networking & Communication Pages: 13

Brand: Yeastar Technology Pages: 62

Brand: TECOM Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands