manualshive.com logo in svg

Cisco Catalyst 3120, Software Manual

The Cisco Catalyst 3120 Hardware Installation Manual is a comprehensive guide that ensures seamless setup of this powerful networking device. It provides step-by-step instructions for hassle-free installation and configuration. Download the manual for free from 88.208.23.73:8080 and unleash the full potential of your Cisco Catalyst 3120.

Share
Download
background image

 

13-3

Cisco Catalyst Blade Switch 3120 for HP Software Configuration Guide

OL-12247-01

Chapter 13      Configuring VTP

Understanding VTP

For domain name and password configuration guidelines, see the 

“VTP Configuration Guidelines” 

section on page 13-8

.

VTP Modes

You can configure a supported switch or switch stack to be in one of the VTP modes listed in 

Table 13-1

.

VTP Advertisements

Each switch in the VTP domain sends periodic global configuration advertisements from each trunk port 
to a reserved multicast address. Neighboring switches receive these advertisements and update their VTP 
and VLAN configurations as necessary.

Note

Because trunk ports send and receive VTP advertisements, you must ensure that at least one trunk port 
is configured on the switch or switch stack and that this trunk port is connected to the trunk port of 
another switch. Otherwise, the switch cannot receive any VTP advertisements. For more information on 
trunk ports, see the 

“Configuring VLAN Trunks” section on page 12-16

.

Table 13-1

VTP Modes

VTP Mode

Description

VTP server

In VTP server mode, you can create, modify, and delete VLANs, and specify other configuration 
parameters (such as the VTP version) for the entire VTP domain. VTP servers advertise their VLAN 
configurations to other switches in the same VTP domain and synchronize their VLAN configurations with 
other switches based on advertisements received over trunk links.

In VTP server mode, VLAN configurations are saved in NVRAM. VTP server is the default mode.

VTP client

A VTP client behaves like a VTP server and transmits and receives VTP updates on its trunks, but you 
cannot create, change, or delete VLANs on a VTP client. VLANs are configured on another switch in the 
domain that is in server mode.

In VTP client mode, VLAN configurations are not saved in NVRAM.

VTP  transparent VTP transparent switches do not participate in VTP. A VTP transparent switch does not advertise its VLAN 

configuration and does not synchronize its VLAN configuration based on received advertisements. 
However, in VTP Version 2, transparent switches do forward VTP advertisements that they receive from 
other switches through their trunk interfaces. You can create, modify, and delete VLANs on a switch in 
VTP transparent mode. 

The switch must be in VTP transparent mode when you create extended-range VLANs. See the 

“Configuring Extended-Range VLANs” section on page 12-12

. 

The switch must be in VTP transparent mode when you create private VLANs. See 

Chapter 15, 

“Configuring Private VLANs.”

 When private VLANs are configured, do not change the VTP mode from 

transparent to client or server mode. 

When the switch is in VTP transparent mode, the VTP and VLAN configurations are saved in NVRAM, 
but they are not advertised to other switches. In this mode, VTP mode and domain name are saved in the 
switch running configuration, and you can save this information in the switch startup configuration file by 
using the copy running-config startup-config privileged EXEC command. The running configuration and 
the saved configuration are the same for all switches in a stack.

Summary of Contents for Catalyst 3120









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 3120

SonicWALL SonicWALL TZ Getting Started Manual preview
SonicWALL TZ
Brand: SonicWALL Pages: 38
DigiFlak Flak Installation Manual preview
Flak
Brand: DigiFlak Pages: 10
PaloAlto Networks PA-5200 Series Quick Start Manual preview
PA-5200 Series
Brand: PaloAlto Networks Pages: 2
Lanner electronics FW-6420 User Manual preview
FW-6420
Brand: Lanner electronics Pages: 48
Fortinet FortiWiFi FortiWiFi-50B Install Manual preview
FortiWiFi FortiWiFi-50B
Brand: Fortinet Pages: 68
Dell 9200 Owner'S Manual preview
9200
Brand: Dell Pages: 174
Dell 9200 Service Manual preview
9200
Brand: Dell Pages: 115
Cisco 2100 Series Configuration Manual preview
2100 Series
Brand: Cisco Pages: 796

Brands by name

Popular brands

Load more brands