manualshive.com logo in svg

Cisco Catalyst 3120, Software Manual

The Cisco Catalyst 3120 Hardware Installation Manual is a comprehensive guide that ensures seamless setup of this powerful networking device. It provides step-by-step instructions for hassle-free installation and configuration. Download the manual for free from 88.208.23.73:8080 and unleash the full potential of your Cisco Catalyst 3120.

Share
Download
background image

 

37-6

Cisco Catalyst Blade Switch 3120 for HP Software Configuration Guide

OL-12247-01

Chapter 37      Configuring EtherChannels and Link-State Tracking

Understanding EtherChannels

Use the silent mode when the switch is connected to a device that is not PAgP-capable and seldom, if 
ever, sends packets. An example of a silent partner is a file server or a packet analyzer that is not 
generating traffic. In this case, running PAgP on a physical port connected to a silent partner prevents 
that switch port from ever becoming operational. However, the silent setting allows PAgP to operate, to 
attach the port to a channel group, and to use the port for transmission.

PAgP Interaction with Other Features 

The Dynamic Trunking Protocol (DTP) and the Cisco Discovery Protocol (CDP) send and receive 
packets over the physical ports in the EtherChannel. Trunk ports send and receive PAgP protocol data 
units (PDUs) on the lowest numbered VLAN. 

In Layer 2 EtherChannels, the first port in the channel that comes up provides its MAC address to the 
EtherChannel. If this port is removed from the bundle, one of the remaining ports in the bundle provides 
its MAC address to the EtherChannel. For Layer 3 EtherChannels, the MAC address is allocated by the 
stack master as soon as the interface is created (through the interface port-channel global configuration 
command).

PAgP sends and receives PAgP PDUs only from ports that are up and have PAgP enabled for the auto or 
desirable mode.

Link Aggregation Control Protocol

The LACP is defined in IEEE 802.3ad and enables Cisco switches to manage Ethernet channels between 
switches that conform to the IEEE 802.3ad protocol. LACP facilitates the automatic creation of 
EtherChannels by exchanging LACP packets between Ethernet ports. 

By using LACP, the switch or switch stack learns the identity of partners capable of supporting LACP 
and the capabilities of each port. It then dynamically groups similarly configured ports into a single 
logical link (channel or aggregate port). Similarly configured ports are grouped based on hardware, 
administrative, and port parameter constraints. For example, LACP groups the ports with the same speed, 
duplex mode, native VLAN, VLAN range, and trunking status and type. After grouping the links into an 
EtherChannel, LACP adds the group to the spanning tree as a single switch port.

LACP Modes

Table 37-2

 shows the user-configurable EtherChannel LACP modes for the channel-group interface 

configuration command. 

Both the active and passive LACP modes enable ports to negotiate with partner ports to an 
EtherChannel based on criteria such as port speed and, for Layer 2 EtherChannels, trunking state and 
VLAN numbers. 

Table 37-2

EtherChannel LACP Modes

Mode

Description

active 

Places a port into an active negotiating state in which the port starts negotiations with other 
ports by sending LACP packets.

passive 

Places a port into a passive negotiating state in which the port responds to LACP packets 
that it receives, but does not start LACP packet negotiation. This setting minimizes the 
transmission of LACP packets.

Summary of Contents for Catalyst 3120









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 3120

NETGEAR FWG114P - ProSafe 802.11g Wireless Firewall Reference Manual preview
FWG114P - ProSafe 802.11g Wireless Firewall
Brand: NETGEAR Pages: 70
3Com 3CR3MFA-92 User Manual preview
3CR3MFA-92
Brand: 3Com Pages: 154
Nexcom NSA 1160 User Manual preview
NSA 1160
Brand: Nexcom Pages: 71
NetPilot NetPilot Globemaster Getting Started Manual preview
NetPilot Globemaster
Brand: NetPilot Pages: 36
Palo Alto PA-800 Series Hardware Reference Manual preview
PA-800 Series
Brand: Palo Alto Pages: 44
Nokia EM7500 Installation Manual preview
EM7500
Brand: Nokia Pages: 118
Nokia IP110 Product Manual preview
IP110
Brand: Nokia Pages: 24
Barracuda SSL VPN Quick Start Manual preview
SSL VPN
Brand: Barracuda Pages: 2
Dell NSA E5500 Getting Started Manual preview
NSA E5500
Brand: Dell Pages: 74
Infoblox Infoblox-1852-A Installation Manual preview
Infoblox-1852-A
Brand: Infoblox Pages: 20
Infoblox Infoblox-1050-A Installation Manual preview
Infoblox-1050-A
Brand: Infoblox Pages: 28
Infoblox Infoblox-550 User Manual preview
Infoblox-550
Brand: Infoblox Pages: 40
Advantech FWA-3140 User Manual preview
FWA-3140
Brand: Advantech Pages: 23

Brands by name

Popular brands

Load more brands