manualshive.com logo in svg

Cisco Catalyst 3120, Software Manual

The Cisco Catalyst 3120 Hardware Installation Manual is a comprehensive guide that ensures seamless setup of this powerful networking device. It provides step-by-step instructions for hassle-free installation and configuration. Download the manual for free from 88.208.23.73:8080 and unleash the full potential of your Cisco Catalyst 3120.

Share
Download
background image

 

39-18

Cisco Catalyst Blade Switch 3120 for HP Software Configuration Guide

OL-12247-01

Chapter 39      Configuring IPv6 Unicast Routing

Configuring IPv6

To disable IPv6 CEF or distributed CEF, use the no ipv6 cef or no ipv6 cef distributed global 
configuration command. To reenable IPv6 CEF or dCEF if it has been disabled, use the ipv6 cef or ipv6 
cef distributed global configuration command. You can verify the IPv6 state by entering the show ipv6 
cef privileged EXEC command.

Configuring Static Routing for IPv6

Static routes are manually configured and define an explicit route between two networking devices. The 
benefits of static routes include security and resource efficiency. Static routes use less bandwidth than 
dynamic routing protocols because there is no requirement for routes to be calculated and 
communicated. The main disadvantage of using static routes is that static routes are not automatically 
updated, as with a dynamic routing protocol, and must be manually reconfigured if the network topology 
changes. Static routes are useful for smaller networks with only one path to an outside network or to 
provide security for a larger network for certain types of traffic.

There are types of static routes:

•

Directly attached static routes—Only the output interface is specified because the destination is 
assumed to be directly attached to this interface. The packet destination is used as the next hop 
address. A directly attached static route is valid only when the specified interface is IPv6-enabled 
and is up.

•

Recursive static routes—Only the next hop is specified, and the output interface is derived from the 
next hop. A recursive static route is valid only when the specified next hop results in a valid IPv6 
output interface, the route does not self-recur, and the recursion depth does not exceed the maximum 
IPv6 forwarding recursion depth.

•

Fully specified static routes—Both the output interface and the next hop are specified. The next hop 
is assumed to be directly attached to the specified output interface. A fully specified route is valid 
when the specified IPv6 interface is IPv6-enabled and up.

•

Floating static routes—Any of the three types of static routes can be floating static routes, used to 
back up dynamic routes learned through configured routing protocols. A floating static route is 
configured with a less efficient administrative distance than the routing protocol it is backing up. 
Therefore, the dynamic route is always used for routing traffic in preference to the floating static 
route. If the dynamic route is lost, the floating static route is used in its place. 

Note

Before configuring a static IPv6 route, you must enable routing by using the ip routing global 
configuration command, enable the forwarding of IPv6 packets by using the ipv6 unicast-routing global 
configuration command, and enable IPv6 on at least one Layer 3 interface by configuring an IPv6 
address on the interface.

Summary of Contents for Catalyst 3120









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 3120

BENDIX VM-3 FIREWALL MANIFOLD Instructions preview
VM-3 FIREWALL MANIFOLD
Brand: BENDIX Pages: 4
Black Box Programmable Security Guard Manual preview
Programmable Security Guard
Brand: Black Box Pages: 33
Fortinet FortiGate 1000A Administration Manual preview
FortiGate 1000A
Brand: Fortinet Pages: 412
Lancom R&S Unified AGPO150 Migration Manual preview
R&S Unified AGPO150
Brand: Lancom Pages: 17
Watchguard Firebox SOHO 6 Wireless Quick Start Manual preview
Firebox SOHO 6 Wireless
Brand: Watchguard Pages: 2
H3C SecPath F100-X-G3 Installation Manual preview
SecPath F100-X-G3
Brand: H3C Pages: 71
Watchguard Firebox M4600 Hardware Manual preview
Firebox M4600
Brand: Watchguard Pages: 34

Brands by name

Popular brands

Load more brands