manualshive.com logo in svg

Cisco Catalyst 3120, Software Manual

The Cisco Catalyst 3120 Hardware Installation Manual is a comprehensive guide that ensures seamless setup of this powerful networking device. It provides step-by-step instructions for hassle-free installation and configuration. Download the manual for free from 88.208.23.73:8080 and unleash the full potential of your Cisco Catalyst 3120.

Share
Download
background image

 

44-5

Cisco Catalyst Blade Switch 3120 for HP Software Configuration Guide

OL-12247-01

Chapter 44      Configuring IP Multicast Routing

Understanding Cisco’s Implementation of IP Multicast Routing

When a new receiver on a previously pruned branch of the tree joins a multicast group, the PIM DM 
device detects the new receiver and immediately sends a graft message up the distribution tree toward 
the source. When the upstream PIM DM device receives the graft message, it immediately puts the 
interface on which the graft was received into the forwarding state so that the multicast traffic begins 
flowing to the receiver. 

PIM-SM

PIM-SM uses shared trees and shortest-path-trees (SPTs) to distribute multicast traffic to multicast 
receivers in the network. In PIM-SM, a router or multilayer switch assumes that other routers or switches 
do not forward multicast packets for a group, unless there is an explicit request for the traffic (join 
message). When a host joins a multicast group using IGMP, its directly connected PIM-SM device sends 
PIM join messages toward the root, also known as the RP. This join message travels router-by-router 
toward the root, constructing a branch of the shared tree as it goes. 

The RP keeps track of multicast receivers. It also registers sources through register messages received 
from the source’s first-hop router (designated router [DR]) to complete the shared tree path from the 
source to the receiver. When using a shared tree, sources must send their traffic to the RP so that the 
traffic reaches all receivers. 

Prune messages are sent up the distribution tree to prune multicast group traffic. This action permits 
branches of the shared tree or SPT that were created with explicit join messages to be torn down when 
they are no longer needed.

When the number of PIM-enabled interfaces exceeds the hardware capacity and PIM-SM is enabled with 
the SPT threshold is set to infinity, the switch does not create (S,G) entries in the multicast routing table 
for the some directly connected interfaces if they are not already in the table. The switch might not 
correctly forward traffic from these interfaces.

PIM Stub Routing

The PIM stub routing feature, available in all software images, reduces resource usage by moving routed 
traffic closer to the end user.

Note

The IP base image contains only PIM stub routing. The IP services image contains complete multicast 
routing. On a switch running the IP base image, if you try to configure a VLAN interface with PIM 
dense-mode, sparse-mode, or dense-sparse-mode, the configuration is not allowed.

In a network using PIM stub routing, the only allowable route for IP traffic to the user is through a switch 
that is configured with PIM stub routing. PIM passive interfaces are connected to Layer 2 access 
domains, such as VLANs, or to interfaces that are connected to other Layer 2 devices. Only directly 
connected multicast (IGMP) receivers and sources are allowed in the Layer 2 access domains. The PIM 
passive interfaces do not send or process any received PIM control packets.

When using PIM stub routing, you should configure the distribution and remote routers to use IP 
multicast routing and configure only the switch as a PIM stub router. The switch does not route transit 
traffic between distribution routers. You also need to configure a routed uplink port on the switch. The 
switch uplink port cannot be used with SVIs. If you need PIM for an SVI uplink port, you should upgrade 
to the IP services feature set.

You must also configure EIGRP stub routing when configuring PIM stub routing on the switch. For more 
information, see the 

“EIGRP Stub Routing” section on page 38-43

.

Summary of Contents for Catalyst 3120









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 3120

IBM Proventia Management SiteProtector SP1001 Getting Started preview
Proventia Management SiteProtector SP1001
Brand: IBM Pages: 2
Fortinet FortiDB-400B Quick Start Manual preview
FortiDB-400B
Brand: Fortinet Pages: 2
Fortinet FortiGate 5050-R Chassis Manual preview
FortiGate 5050-R
Brand: Fortinet Pages: 28
Fortinet FortiGate 3600A Installation Manual preview
FortiGate 3600A
Brand: Fortinet Pages: 64
Fortinet FortiBridge 1000 Installation Manual preview
FortiBridge 1000
Brand: Fortinet Pages: 56
Juniper JSA7800 Quick Start Manual preview
JSA7800
Brand: Juniper Pages: 13
M-Audio FireWire Solo User Manual preview
FireWire Solo
Brand: M-Audio Pages: 20
Pulse Secure PSA3000 Hardware Manual preview
PSA3000
Brand: Pulse Secure Pages: 42
Pulse Secure PSA7000 Hardware Manual preview
PSA7000
Brand: Pulse Secure Pages: 52
Blue Coat MC-S400 Series Quick Start Manual preview
MC-S400 Series
Brand: Blue Coat Pages: 2
AhnLab TrusGuard Installation Manual preview
TrusGuard
Brand: AhnLab Pages: 120

Brands by name

Popular brands

Load more brands