Cisco Catalyst 8200 Series Quick Start Manual Download | Manualshive

Page: 4 / 8

background image

Figure 3: Removing the Chassis Cover

5.

Lift the chassis cover after you have removed all the screws.

To replace the chassis cover, place the cover evenly on the top of the device and use the screws to secure it
to the device.

Note

Installing a DIMM

There are two DDR4 DIMM slots. DIMMs have a polarization notch on the connecting edge to prevent
incorrect insertion.

Figure 4: DIMM Showing Polarization Notch

Polarization Notch

1

Installing and Upgrading Field Replaceable Units

4

Installing and Upgrading Field Replaceable Units

Installing a DIMM

«
...
2
3
4
5
6
...
»

Summary of Contents for Catalyst 8200 Series









Reviews:

No comments

Related manuals for Catalyst 8200 Series

Brand: Pathport Pages: 2

Brand: Juniper Pages: 2

Brand: THOMSON Pages: 90

Brand: FACTBIRD Pages: 2

Brand: Planet Pages: 57

Brand: Extron electronics Pages: 23

Brand: DAUDIN Pages: 24

Brand: Innoband Pages: 131

Brand: LG Pages: 11

AC Smart BACnet

Brand: LG Pages: 88

BECON HVAC BACnet PQNFB17C0

Brand: LG Pages: 118

Brand: LG Pages: 220

Brand: LG Pages: 481

Brand: LG Pages: 2

Brand: 2N Pages: 113

Brand: IFM Electronic Pages: 65

Brand: IFM Pages: 28

Brand: IFM Pages: 85

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands