Cisco Expressway CE1000 Appliance Installation Manual Download

Page: 5 / 16

Preparing to install

Environmental and power specifications

To view environmental and power specifications for the appliance server see

http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C220/install/spec.html

Unpacking the unit and preparing the installation

See

http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C220/install/install.html

for information

on:

Unpacking and inspecting the server
Note that the CE1000 is shipped with 2 x 10 Gb fiber SFPs and 2 x 1 Gb copper SFPs.

Installation guidelines

Rack requirements

Equipment requirements

Slide rail adjustment range

Locating serial numbers

The Cisco Expressway appliance displays two serial numbers:

UCS serial number:

has the format FCHxxxxxxxx

is displayed on the physical hardware and in the CIMC web interface

Application/Software serial number:

has the format 52XNNNNN, where X is a letter and N are numbers

is displayed in the Cisco Expressway web interface, console and SSH session

must be supplied to obtain release and option keys

Cisco Expressway CE1000 Appliance Installation Guide (8.5)

Page 5 of 16

Preparing to install

Summary of Contents for Expressway CE1000 Appliance

















Search results

Summary of Contents for Expressway CE1000 Appliance

Reviews:

Related manuals for Expressway CE1000 Appliance

Brands by name

Popular brands

Cisco Expressway CE1000 Appliance, Installation Manual

Search results

Summary of Contents for Expressway CE1000 Appliance

Reviews:

Related manuals for Expressway CE1000 Appliance

Brands by name

Popular brands