background image

 

Chapter 2      Processor Cards Feature Summary

Analog Station Interface Cards

2-22

Cisco ICS 7750 System Description

78-10360-02

Analog Station Interface Cards

Analog station interface (ASI) cards enable you to connect to analog telephones, 
fax machines, and teleconferencing stations. Two ASI cards are available:

ASI81—Contains an 8-port Foreign Exchange Station (FXS) module and any 
one of the VIC, WIC, or VWIC modules shown in 

Table 2-6

 that support 

digital and analog voice trunks and WAN routing interfaces, completely 
integrating voice and data networking.

MRP3-8FXS—Contains an 8-port FXS module and onboard Flash memory.

ASI160—Contains a 16-port FXS module.

MRP3-16FXS—Contains a 16-port FXS module and onboard Flash memory.

ASI cards can reside in any of the interchangeable slots (slot 1 through slot 6). 

Figure 2-6

 shows the ASI81 card. 

Figure 2-7

 shows the ASI160 card.

Note

For information about the VICs, WICs, and VWICs that are supported on the 
ASI81 card, see the 

“Voice and WAN Interface Cards” section on page 2-29

.

Summary of Contents for ICS-7750















































































































































































Reviews: