Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 104 / 516

background image

Step 9

If you use redundant power leads, terminate the return 2 lead to the positive RET2 terminal on the ONS 15454.
Terminate the negative 2 lead to the negative BAT2 terminal on the ONS 15454. Use oxidation-preventative
grease to keep connections noncorrosive.

The configured ONS 15454 shelf can work with a single power line since the ONS 15454 power
configuration offers redundancy. When using the 15454-FTA3 fan-tray, if the ONS15454 shelf is
powered by a single power line, the BAT-FAIL alarm appears, the fans run at a maximum speed,
and the system does not comply with NEBS GR-63 Issue 3 and GR-1089 Issue 4 and 5 requirements.
In order to meet the above mentioned NEBS requirements, the ONS 15454 shelf must be powered
by both the DC power lines.

Note

Step 10

Route the cables out below the power terminals using the plastic cable clamp, as shown in

Figure 40: Cisco

ONS 15454 Power Terminals, on page 73

.

Step 11

Connect the return cables to earth ground at power supply side.

Step 12

Return to your originating procedure (NTP).

DLP-G19 Turn On and Verify Office Power

This task measures the power to verify correct power and returns for the ONS
15454 shelf.

Purpose

Voltmeter

Tools/Equipment

ETSI:

• Connect the office ground to chassis. For detailed instructions on grounding,

refer to the

Electrostatic Discharge and Grounding Guide for Cisco CPT and

Cisco ONS Platforms

.

•

DLP-G17 Connect Office Power to the ONS 15454 ETSI , on page 70

•

DLP-G18 Connect Office Power to the ONS 15454 ANSI, on page 71

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Do not apply power to the shelf until you complete all installation steps.

Caution

Procedure

Step 1

Using a voltmeter, verify the office battery and ground at the following points on the fuse and alarm panel:

a) To verify the power, place the black test lead of the voltmeter to the frame ground. Place the red test lead

on the A-side connection and verify that it is between –40.5 VDC and –57 VDC. Place the red test lead
on the B-side connection and verify that it is between –40.5 VDC and –57 VDC.

Cisco ONS 15454 Hardware Installation Guide

74

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

DLP-G19 Turn On and Verify Office Power

«
...
102
103
104
105
106
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

SnapServer NAS N2000

Brand: Overland Storage Pages: 4

Brand: Accuride Pages: 2

Brand: AirLive Pages: 12

Brand: National Instruments Pages: 4

SnapExpansion DX Series

Brand: Overland Storage Pages: 3

IE-MediaChassis/1-AC

Brand: B+B SMARTWORK Pages: 12

Brand: Siemens Pages: 8

Elgar ReFlex Power

Brand: Ametek Pages: 359

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands