Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 166 / 516

background image

Step 2

Use the latches/ejectors to firmly slide the card along the guide rails in Slot 9 until the card plugs into the
receptacle at the back of the slot.

Step 3

Verify that the card is inserted correctly and close the latches/ejectors on the card.

It is possible to close the latches/ejectors when the card is not completely plugged into the backplane.
Ensure that you cannot insert the card any further.

Note

Step 4

Verify the following:

• The red FAIL LED blinks for up to 10 seconds.

If the red FAIL LED does not turn on, check the power.

Note

• The PWR A and PWR B LEDs become red, the two INPUT/OUTPUT LEDs become amber, and the

ACT LED turns green for approximately 5 seconds.

• The PWR A and PWR B LEDs turn green, the INPUT/OUTPUT LEDs turn off, and the green ACT LED

remains on.

It might take up to 3 minutes for the PWR A and PWR B LEDs to update.

Note

If you insert a card into a slot provisioned for a different card, no LEDs turn on.

Note

If the red FAIL LED is on continuously or the LEDs act erratically, the card is not installed properly.
Remove the card and repeat all the steps.

Note

Step 5

Return to your originating procedure (NTP).

DLP-G309 Install the MS-ISC-100T Card

This task installs redundant MS-ISC-100T cards. The MS-ISC-100T card is
required for a multishelf node configuration. It provides LAN redundancy on the
node controller shelf. An alternative to using the MS-ISC-100T card is the Cisco
Catalyst 2950, although Cisco recommends using the MS-ISC-100T. For more
information on the Catalyst 2950 installation, refer to the Catalyst 2950 product
documentation.

Purpose

MS-ISC-100T card (2)

Tools/Equipment

DLP-G33 Install the TCC2, TCC2P, or TCC3 Card , on page 132

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

When installing cards, allow each card to boot completely before installing the next card.

Note

Cisco ONS 15454 Hardware Installation Guide

136

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

DLP-G309 Install the MS-ISC-100T Card

«
...
164
165
166
167
168
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Echo Express SEL

Brand: Sonnet Pages: 16

Echo Express III-D

Brand: Sonnet Pages: 18

IE-MediaChassis/2

Brand: B&B Electronics Pages: 13

Brand: Campbell Pages: 26

SPICER PACCAR 220ev

Brand: DANA Pages: 761

Brand: Patton electronics Pages: 51

DMC 1000 - Modular Expansion Base

Brand: D-Link Pages: 16

apollo 4510 gen9

Brand: HP Pages: 68

BladeSystem c7000

Brand: HP Pages: 80

Brand: HP Pages: 49

Brand: Thermaltake Pages: 12

Brand: Thermaltake Pages: 20

Brand: JYTEK Pages: 32

Brand: JYTEK Pages: 35

Brand: iStarUSA Pages: 3

Brand: iStarUSA Pages: 3

Brand: iStarUSA Pages: 3

Brand: iStarUSA Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands