Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 238 / 516

background image

DLP-G588 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for
ETSI Rack Configuration

This task installs the bracket with air deflectors (front-to-top configuration) on
the ONS 15454 M2 shelf.

Purpose

• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver

Tools/Equipment

NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454
M6 Shelves, on page 20

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Use only the fastening hardware provided with the ONS 15454 M2 to prevent loosening, deterioration, and
electromechanical corrosion of the hardware and joined material.

Caution

The air deflectors can be installed only in the front position of the chassis.

Note

Procedure

Step 1

Place the right front air deflector flush against the right side of the chassis (see Diagram 1 of

Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack
Configuration, on page 209

).

Step 2

Align the screw holes on the right front air deflector with the screw holes on right side of the chassis.

Step 3

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 4

Place the air deflector cover on the rear end of the chassis.

Step 5

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See Diagram 2 of

Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack
Configuration, on page 209

).

Step 6

Place the mounting bracket flush against the left side of the chassis (see Diagram 2 of

Figure 129: Mounting

the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration,
on page 209

Step 7

Align the screw holes on the mounting bracket with the screw holes on the left side of the chassis.

Step 8

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 9

Place the mounting bracket flush against the right side of the chassis (see Diagram 2 of

Figure 129: Mounting

the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration,
on page 209

Cisco ONS 15454 Hardware Installation Guide

208

Installing the ONS 15454 M2 Shelf

DLP-G588 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

«
...
236
237
238
239
240
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Ethernet Routing Switch 8010

Brand: Nortel Pages: 16

Brand: Supermicro Pages: 146

Megaplex II 4U Guide

Brand: American Megatrends Pages: 26

Brand: National Instruments Pages: 12

Brand: Barco Pages: 39

Brand: National Instruments Pages: 9

Brand: Cisco Pages: 1218

Brand: Supero Pages: 39

Brand: Moxa Technologies Pages: 6

Brand: Enlight Pages: 45

Brand: Changhong Electric Pages: 34

FortiGate FortiGate-5050

Brand: Fortinet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands