manualshive.com logo in svg

Cisco ONS 15454, Hardware Installation Manual

The Cisco ONS 15454 is a cutting-edge networking device that offers unmatched performance and reliability. Explore its full potential by accessing the comprehensive Procedure Manual, available for free download on our website. Maximize your understanding and utilization of this product for seamless connectivity and efficient operations.

Share
Download
background image

The ONS 15454 M2 requires a minimum of 20.4-inches (518.16-mm) vertical length and a minimum of
25.5-inches (647.69-mm) horizontal width on the wall. Wall mount brackets are used to mount the ONS 15454
M2 shelf assembly on the wall. The type of screws used to mount the brackets on the wall depends on the
wall-type and are not provided by Cisco. The screws used must be able to sustain an overall weight of at least
20 kg (44 lb).

Note

Procedure

Step 1

Verify that the proper fuse panel has been installed. If a fuse panel is not present, you must install one according
to manufacturer instructions:

• For a DC power supply, the fuse rating must not exceed 15A.
• For an AC power supply, the fuse rating must not exceed 10A, 15A, or 20A. For North America, the

branch circuit protection must be rated 20A. The overcurrent/short circuit protection must be in accordance
with local and national electrical codes.

Step 2

Mount the bracket on the wall as shown in

Figure 131: Wall Mounting of the ONS 15454 M2 Shelf, on page

213

. To mount the bracket on a non-concrete wall, choose the bracket holes based on the wall structure. At

least four screws must be used to mount the bracket on the wall.

Step 3

Align the mounting bracket screw holes against the shelf screw holes (see diagram 1 of

Figure 131: Wall

Mounting of the ONS 15454 M2 Shelf, on page 213

).

Step 4

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See diagram 2 of

Figure 131:

Wall Mounting of the ONS 15454 M2 Shelf, on page 213

.

Cisco ONS 15454 Hardware Installation Guide

212

Installing the ONS 15454 M2 Shelf

DLP-G590 Mount the ONS 15454 M2 Shelf on the Wall

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

IBM 3455-D3E Install Manual preview
3455-D3E
Brand: IBM Pages: 46
Sanyo 14GX37 Service Manual preview
14GX37
Brand: Sanyo Pages: 39
TP-Link TL-MC1400 User Manual preview
TL-MC1400
Brand: TP-Link Pages: 14
Supero SC812 Series Installation Manual preview
SC812 Series
Brand: Supero Pages: 16
Supero SC812L Series User Manual preview
SC812L Series
Brand: Supero Pages: 52
Supero SC835 Chassis Series User Manual preview
SC835 Chassis Series
Brand: Supero Pages: 66
Supero SC825TQ-560LPV User Manual preview
SC825TQ-560LPV
Brand: Supero Pages: 82
Supero SC523 Series User Manual preview
SC523 Series
Brand: Supero Pages: 49
Supero SC815S-560 User Manual preview
SC815S-560
Brand: Supero Pages: 84
Supero SC811i-260 User Manual preview
SC811i-260
Brand: Supero Pages: 82
Supero SC747TQ-R1400B User Manual preview
SC747TQ-R1400B
Brand: Supero Pages: 80
Supero SC512C-260 Series User Manual preview
SC512C-260 Series
Brand: Supero Pages: 66
Supero SC733E-465B User Manual preview
SC733E-465B
Brand: Supero Pages: 70
Supero SC743i-465 User Manual preview
SC743i-465
Brand: Supero Pages: 94
Otto Bock KIMBA 2231 Instructions For Use Manual preview
KIMBA 2231
Brand: Otto Bock Pages: 20

Brands by name

Popular brands

Load more brands