Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 267 / 516

background image

Step 2

Push the fan-tray assembly such that the backplane connector is completely engaged (see the following figure).

Figure 159: Inserting the Fan-Tray Assembly in the ONS 15454 M2 Chassis

Step 3

Tighten the screw to a torque value of 4 in-lb (0.45 N-m) to lock the unit (see the following figure).

Figure 160: Fan-Tray Assembly Installed in the ONS 15454 M2 Shelf

Step 4

To verify that the tray has plugged into the assembly, check the fan-tray and listen to determine if the fans
are running.

If the fan-tray assembly is removed from the shelf, wait for at least 5 seconds before plugging it
back into the shelf. In the event the LCD display on the fan-tray assembly appears blank, remove
the unit from the shelf, wait for at least 5 seconds and reinsert the unit into the shelf.

Note

Stop. You have completed this procedure.

Power and Ground Description

Ground the equipment according to Telcordia standards or local practices.

The grounding configuration is mandatory for ANSI and ETSI chassis for both AC and DC configurations.

The following sections describe power and ground for the ONS 15454 M2 shelves.

For detailed instructions on grounding the ONS 15454 M2 chassis, see the

Electrostatic Discharge and

Grounding Guide for Cisco CPT and Cisco ONS Platforms

Cisco ONS 15454 Hardware Installation Guide

237

Installing the ONS 15454 M2 Shelf

Power and Ground Description

«
...
265
266
267
268
269
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

iConverter 8245-11pt

Brand: Omnitron Systems Pages: 8

Brand: Overland Storage Pages: 3

MHUB PRO (8X8) 70

Brand: HDanywhere Pages: 2

Brand: Ambient Recording Pages: 15

FastIron SX 1600

Brand: Brocade Communications Systems Pages: 12

Network Convergence System 6000 Fabric Card Chassis

Brand: Cisco Pages: 202

Nexus 3000 series

Brand: Cisco Pages: 356

Brand: Cisco Pages: 34

Brand: Cisco Pages: 402

Brand: Cisco Pages: 508

Brand: Cisco Pages: 12

NCS 4000 Series

Brand: Cisco Pages: 82

Brand: Cisco Pages: 85

Modular Matrix 38250

Brand: Lindy Pages: 8

RMC4136-670-HSE

Brand: Gooxi Pages: 27

Brand: Hypercom Pages: 198

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands