Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 271 / 516

background image

This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than: 10A-20A, 100-240 VAC~.

Statement 1005

Warning

A readily accessible two-poled disconnect device must be incorporated in the fixed wiring.

Statement

1022

Warning

This unit might have more than one power supply connection. All connections must be removed to
de-energize the unit.

Statement 1028

Warning

Always use the supplied ESD wristband when working with a powered ONS 15454. For detailed instructions
on how to wear the ESD wristband, refer to the

Electrostatic Discharge and Grounding Guide for Cisco CPT

and Cisco ONS Platforms

.

Caution

Procedure

Step 1

Verify that the correct fuse panel is installed in the top mounting space:

• For a DC power supply, the fuse rating must not exceed 15A.

• For an AC power supply, the fuse rating must not exceed 10A, 15A, or 20A. For low input voltage ranges,

100V to 127Vac, the branch circuit protection must not be rated more than 20A. The overcurrent/short
circuit protection must be in accordance with local and national electrical codes.

Step 2

Depending on the shelf and the power module installed, complete the necessary tasks:

•

DLP-G596 Connect Office Power (AC) to the ONS 15454 M2 Shelf, on page 241

•

DLP-G597 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ANSI Only), on page 244

•

DLP-G598 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ETSI Only), on page 249

Step 3

Connect the office ground to the ONS 15454 M2 shelf. For detailed instructions on grounding, refer to the

Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms

.

Step 4

Complete the

DLP-G600 Turn On and Verify DC Office Power on the ONS 15454 M2 Shelf, on page 252

Step 5

Continue with the

NTP-G268 Install the Fan-Tray Assembly in the ONS 15454 M2 Shelf, on page 235

Stop. You have completed this procedure.

DLP-G596 Connect Office Power (AC) to the ONS 15454 M2 Shelf

This task connects AC power to the ONS 15454 M2 shelf.

Purpose

Cisco ONS 15454 Hardware Installation Guide

241

Installing the ONS 15454 M2 Shelf

DLP-G596 Connect Office Power (AC) to the ONS 15454 M2 Shelf

«
...
269
270
271
272
273
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: National Instruments Pages: 23

Brand: Supermicro Pages: 80

2nd Gen H5 Fanless

Brand: HDPlex Pages: 24

Brand: Supermicro Pages: 160

Project M Chassis

Brand: saberz Pages: 29

FastIron SX 1600

Brand: Brocade Communications Systems Pages: 593

Brand: Supero Pages: 60

Brand: Supero Pages: 28

Brand: Supero Pages: 28

Brand: Supero Pages: 13

Brand: Supero Pages: 67

Brand: Supero Pages: 61

Brand: Supero Pages: 30

Brand: Supero Pages: 124

Brand: Supero Pages: 97

SC847BE1C series

Brand: Supero Pages: 116

Brand: Supero Pages: 82

SC847A-R1400LPB

Brand: Supero Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands