Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 279 / 516

background image

Before you make any crimp connections, coat all bare conductors (battery, battery return, and frame
ground) with an appropriate antioxidant compound. Bring all unplated connectors, braided strap,
and bus bars to a bright finish, then coat with an antioxidant before you connect them. You do not
need to prepare tinned, solder-plated, or silver-plated connectors and other plated connection surfaces,
but always keep them clean and free of contaminants.

Caution

When terminating power, return (RET), and frame ground, do not use soldering lug, screwless
(push-in) connectors, quick-connect, or other friction-fit connectors.

Caution

Step 12

Return to your originating procedure (NTP).

DLP-G598 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ETSI Only)

This task connects power to the ONS 15454 M2 shelf (ETSI Only).

Purpose

• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver
• Wire wrapper
• Wire cutters
• Wire strippers
• Crimp tool
• Fuse panel
• Ground cable #6 AWG stranded. The PID of the DC power cable for ETSI

left exit is 15454-M2-DCCBL-LE=.

Tools/Equipment

•

NTP-G266 Install the ONS 15454 M2 Shelf, on page 194

.

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, refer to the

Electrostatic Discharge and Grounding

Guide for Cisco CPT and Cisco ONS Platforms

.

•

NTP-G270 Open and Remove the Standard Door of the ONS 15454 M2
Shelf, on page 218

.

•

NTP-G267 Install the Power Module in the ONS 15454 M2 Shelf, on page
230

.

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

When installing or replacing the unit, the ground connection must always be made first and disconnected
last.

Statement 1046

Warning

Cisco ONS 15454 Hardware Installation Guide

249

Installing the ONS 15454 M2 Shelf

DLP-G598 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ETSI Only)

«
...
277
278
279
280
281
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: Advantech Pages: 52

Brand: Philips Pages: 122

Brand: Fire-Lite Pages: 1

Brand: Supero Pages: 64

Brand: Supermicro Pages: 34

Brand: Lets Go Aero Pages: 13

Brand: AICSYS Pages: 10

InfinityLink IL6000

Brand: Artel Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands