Cisco ONS 15454 Hardware Installation Manual Download

Page: 338 / 516

Do not mount the left back deflector (exhaust air deflector), if these cards are to be installed in the ONS 15454
M6 shelf:

• 100G-LC-C, 10x10G-LC, or CFP-LC
• EDRA1-26, EDRA1-35, EDRA2-26, or EDRA2-35

Use the standard brackets directly to mount the ONS 15454 M6 shelf.

Step 5

Align the screw holes of the left back air deflector with the screw holes on the left side of the chassis.

Step 6

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 7

Place the mounting bracket flush in the middle position (see Diagram 1 of

Figure 208: Mounting the Bracket

with Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ETSI Rack Configuration, on page 309

)

or the front position (see Diagram 3 of

Figure 208: Mounting the Bracket with Air Deflectors (Front-to-Back)

on the ONS 15454 M6 Shelf for ETSI Rack Configuration, on page 309

) against the right side of the chassis.

Step 8

Align the screw holes on the mounting bracket with the screw holes on the left side of the chassis.

Step 9

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 10

Place the mounting bracket flush in the middle position (see Diagram 1 of

Figure 208: Mounting the Bracket

with Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ETSI Rack Configuration, on page 309

)

or the front position (see Diagram 3 of

Figure 208: Mounting the Bracket with Air Deflectors (Front-to-Back)

on the ONS 15454 M6 Shelf for ETSI Rack Configuration, on page 309

) against the left side of the chassis.

Step 11

Align the screw holes on the mounting bracket with the screw holes on the left side of the chassis.

Step 12

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Figure 207: Mounting the Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ETSI Rack Configuration

Cisco ONS 15454 Hardware Installation Guide

308

Installing the ONS 15454 M6 Shelf

DLP-G564 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ETSI Rack Configuration

Summary of Contents for ONS 15454




































































































































































































































































































































































































































































































































Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands

Cisco ONS 15454, Hardware Installation Manual

Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands