Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 340 / 516

background image

Use only the fastening hardware provided with the ONS 15454 M6 to prevent loosening, deterioration, and
electromechanical corrosion of the hardware and joined material.

Caution

The front-to-top air deflector configuration must be used only for the bottom most chassis in the rack.

Note

Do not install a fan tray (exhaust) side deflector on a chassis that is installed above a chassis with a front-to-top
air deflector configuration.

Note

The front-to-top deflector configuration can be operated at a maximum of 50C at 1800 m altitude. Only
ROADM cards can be installed for this configuration.

Note

It is recommended to maintain a space of one RU between two chassis in a rack for cable management.

Note

Hot and cold aisle airflow management must be planned for the installation.

Note

Procedure

Step 1

To install the mounting bracket with air deflectors (front-to-top) in the front position, perform Step 3 through
Step 11.

Step 2

To install the mounting bracket with air deflectors (front-to-top) in the middle position, perform Step 12
through Step 23.

Step 3

Place the right front air deflector flush against the right side of the chassis (see Diagram 1 of

Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M6 Shelf for ETSI Rack
Configuration- Front Position, on page 311

).

Step 4

Align the screw holes on the right front air deflector with the screw holes on right side of the chassis.

Step 5

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 6

Place a mounting bracket flush against the left and right side of the chassis (see Diagram 2 of

Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M6 Shelf for ETSI Rack
Configuration- Front Position, on page 311

).

Step 7

Align the screw holes on the mounting bracket with the screw holes on the side of the chassis.

Step 8

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 9

Place the left top air deflector flush against the chassis as shown in Diagram 3 of

Figure 209: Mounting the

Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M6 Shelf for ETSI Rack Configuration- Front
Position, on page 311

.

Cisco ONS 15454 Hardware Installation Guide

310

Installing the ONS 15454 M6 Shelf

DLP-G565 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M6 Shelf for ETSI Rack Configuration

«
...
338
339
340
341
342
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: HDPlex Pages: 17

Brand: Omnitron Systems Pages: 4

Brand: Transition Networks Pages: 1

PointSystem CPSMC0100-226

Brand: Transition Networks Pages: 5

Brand: Transition Networks Pages: 5

Brand: Transition Networks Pages: 30

PointSystem CPSMC1900-100

Brand: Transition Networks Pages: 40

PointSystem CPSMC1800-200

Brand: Transition Networks Pages: 42

Brand: JYTEK Pages: 56

Brand: In Win Pages: 15

Brand: ETAS Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands