Cisco ONS 15454 Hardware Installation Manual Download

Page: 344 / 516

Figure 211: Mounting the Bracket with Air Deflectors (Front-to-Side) on the ONS 15454 M6 Shelf for ETSI Rack Configuration

Step 2

Align the screw holes on the right front air deflector with the screw holes on the right side of the chassis.

Step 3

Insert M4 pan-head screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 4

Place the mounting bracket flush in the middle or front position of the right front air deflector (see Diagram
1 of

Figure 212: Mounting the Bracket with Air Deflectors (Front-to-Side) on the ONS 15454 M6 Shelf for

ETSI Rack Configuration - Middle Position, on page 315

Figure 213: Mounting the Bracket with Air

Deflectors (Front-to-Side) on the ONS 15454 M6 Shelf for ETSI Rack Configuration - Front Position, on
page 315

Step 5

Align the screw holes on the mounting bracket with the screw holes on the right front air deflector .

Step 6

Insert M4 flat-head screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 7

Place the mounting bracket flush in the middle or front position on the left side of the chassis (see Diagram
2 of

Figure 212: Mounting the Bracket with Air Deflectors (Front-to-Side) on the ONS 15454 M6 Shelf for

ETSI Rack Configuration - Middle Position, on page 315

Figure 213: Mounting the Bracket with Air

Deflectors (Front-to-Side) on the ONS 15454 M6 Shelf for ETSI Rack Configuration - Front Position, on
page 315

Step 8

Align the screw holes on the mounting bracket with the screw holes on the left side of the chassis.

Step 9

Insert M4 pan-head screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Cisco ONS 15454 Hardware Installation Guide

314

Installing the ONS 15454 M6 Shelf

DLP-G821 Mounting the Bracket with Air Deflectors (Front-to-Side) on the ONS 15454 M6 Shelf for ETSI Rack Configuration

Summary of Contents for ONS 15454




































































































































































































































































































































































































































































































































Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands

Cisco ONS 15454, Hardware Installation Manual

Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands