Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 351 / 516

background image

deep-front panel does not have a hinge and cannot be rotated like the standard door. The fiber or cable guide
used in the ONS 15454 M6 shelf provides improved fiber management.

If a standard front door was ordered, the ONS 15454 M6 is shipped with a preinstalled standard door. If a
deep-front panel was ordered, a temporary front door is preinstalled on the shelf and the deep-front panel is
present in a separate package. If no door was ordered, a temporary front door is preinstalled on the shelf.

The temporary door is used only for shipping purpose and must not be used in the chassis. The temporary
door can be opened by removing the tape that is present on top of the door.

Note

You must remove the door before proceeding with the shelf installation.

The ONS 15454 M6 door can be opened by loosening the front screws and pushing the latch in the opposite
direction. You can remove the front door to provide unrestricted access to the front of the shelf.

An erasable label is pasted on the inside of the front door. You can use the label to record slot and port
assignments, card types, node ID, rack ID, and serial number of the ONS 15454 M6 shelf.

The following figure shows the erasable label on the ONS 15454 M6 shelf.

Figure 216: ONS 15454 M6 Front-Door Erasable Label

The laser warning label is placed on top of the chassis.

The following figure shows the ONS 15454 M6 laser warning.

Cisco ONS 15454 Hardware Installation Guide

321

Installing the ONS 15454 M6 Shelf

Front Door

«
...
349
350
351
352
353
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: Supero Pages: 30

Brand: InWin Pages: 17

PXI EXPRESS PXIe-1095

Brand: National Instruments Pages: 61

Brand: National Instruments Pages: 4

Brand: Cisco Pages: 294

Brand: Cisco Pages: 289

AS5350 - Universal Access Server

Brand: Cisco Pages: 102

Brand: Cisco Pages: 42

Brand: Cisco Pages: 422

Brand: Cisco Pages: 428

Brand: Cisco Pages: 74

Brand: Cisco Pages: 284

Brand: Cisco Pages: 466

Brand: Cisco Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands