Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 369 / 516

background image

Stop. You have completed this procedure.

NTP-G329 Remove the Deep-Front Panel of the ONS 15454 M6
Shelf

This procedure removes the deep-front panel of the ONS 15454 M6 system.

Purpose

• #2 Phillips Dynamometric screwdriver
• Socket (6/32 standard) and socket wrench to tighten or loosen the ground

nut

Tools/Equipment

•

NTP-G252 Install the ONS 15454 M6 Shelf , on page 294

•

NTP-G327 Install the Deep-Front Panel of the ONS 15454 M6 Shelf, on
page 332

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, see the

Electrostatic Discharge and Grounding Guide

for Cisco CPT and Cisco ONS Platforms

.

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

The deep-front panel does not have a hinge and cannot be rotated like a standard door. Rotating the deep-front
panel can damage the deep-front panel, shelf hinges, other devices and cables placed below the ONS 15454
M6 shelf.

Caution

When the deep front-panel is installed, the total chassis depth is 12.9 inches. The deep front-panel extends
from the rack by 1.8 inches.

Note

Procedure

Step 1

Remove the end of the ground strap cable that is connected to the exterior of the deep-front panel (see the
following figure).

Cisco ONS 15454 Hardware Installation Guide

339

Installing the ONS 15454 M6 Shelf

NTP-G329 Remove the Deep-Front Panel of the ONS 15454 M6 Shelf

«
...
367
368
369
370
371
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: Supero Pages: 94

Brand: Ambient Recording Pages: 15

Brand: Skyworth Pages: 50

Brand: IEI Technology Pages: 7

Brand: iXsystems Pages: 12

Brand: Supermicro Pages: 160

Brand: IEI Technology Pages: 11

Brand: VXI Technology Pages: 39

Brand: Norco Pages: 31

Brand: Leckey Pages: 47

Brand: Advantech Pages: 34

Brand: Advantech Pages: 40

Brand: Advantech Pages: 48

Brand: Advantech Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands