Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 462 / 516

background image

Filler and Blank Cards

Filler cards must be installed in unused and empty slots to ensure proper air flow and electromagnetic
interference (EMI) requirements during the ONS 15454 M6 operation. CTC detects filler cards from R 10.6
onwards.

There are two types of card fillers:

• Line card fillers (15454-M-FILLER)

These filler cards operate in slots 2, 3, 4, 5, 6, and 7, and have no card-level LED indicators.

The following figure shows the faceplate of line card filler.

Figure 284: Line Card Filler—Faceplate

• Timing and Control Card fillers (15454-M-T-FILLER)

These filler cards are for control cards that operate in slots 1 and 8. The following figure shows the faceplate
of timing and control card filler.

Figure 285: Timing and Control Card Fillers - Faceplate

Blank cards (15454-BLANK) can be installed in any empty slot in the shelf. CTC does not detect blank cards.
The following figure shows the faceplate of the blank card filler.

Figure 286: Blank Card Filler - Faceplate

Air Filter

The ONS 15454 M6 contains a preinstalled reusable air filter (15454 M6-FTF) on the right side of the shelf.

The reusable filter is made up of a gray, open-cell, polyurethane foam that is specially coated to provide fire
and fungi resistance. Spare filters should be kept in stock. Inspect the air filter every 30 days, and clean the
filter every 3 to 6 months. The air filter can be replaced without removing the fan-tray assembly. However,
the fan-tray must be turned off to remove the air filter. Replace the air filter every two to three years. Avoid
cleaning the air filter with harsh cleaning agents or solvents.

Do not operate an ONS 15454 M6 without the mandatory air filter.

Caution

Cisco ONS 15454 Hardware Installation Guide

432

Installing the ONS 15454 M6 Shelf

Filler and Blank Cards

«
...
460
461
462
463
464
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

ValkyrieBay Val-C12-720G

Brand: Xena Networks Pages: 15

Brand: Samsung Pages: 93

1RK-CHASSIS ONErack

Brand: Tvone Pages: 8

Brand: IBM Pages: 78

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 62

Brand: IMC Networks Pages: 2

Brand: Wesena Pages: 12

Brand: Supero Pages: 16

Brand: Supero Pages: 52

SC835 Chassis Series

Brand: Supero Pages: 66

Brand: Supero Pages: 82

Brand: Supero Pages: 49

Brand: Supero Pages: 84

Brand: Supero Pages: 82

Brand: Supero Pages: 80

SC512C-260 Series

Brand: Supero Pages: 66

Brand: Supero Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands