Cisco ONS 15454 Hardware Installation Manual Download

Page: 474 / 516

Stop. You have completed this procedure.

NTP-G263 Replace the Air Filter of the AC Power Module in the
ONS 15454 M6 Shelf Assembly

This procedure replaces the air filter of the AC power module in the ONS 15454
M6 shelf assembly.

Purpose

New air filter

Tools/Equipment

•

NTP-G252 Install the ONS 15454 M6 Shelf , on page 294

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, refer to the

Electrostatic Discharge and Grounding

Guide for Cisco CPT and Cisco ONS Platforms

•

DLP-G569 Install the AC Power Module in the ONS 15454 M6 Shelf, on
page 355

Prerequisite Procedures

As Needed

Required/As Needed

Remote

Onsite/Remote

Provisioning or higher

Security Level

The air filters are single-use only. They must not be cleaned and reused. This is a Telcordia NEBS requirement,
GR-63-CORE Issue 4.

Note

Air filters must be inspected every month. If they are dirty or clogged with dust, they must be replaced with
a new air filter.

Note

Procedure

Step 1

Open the front door of the shelf assembly (see

DLP-G576 Open the Standard Door of the ONS 15454 M6

Shelf , on page 328

). If the shelf assembly does not have a front door, continue with Step 3.

Step 2

(Optional) Complete the

DLP-G577 Remove the Standard Door of the ONS 15454 M6 Shelf , on page 330

remove the front door. If you do not want to remove the door, proceed to Step 3.

Step 3

Remove the air filter on the AC power module (see

Figure 292: Replacing the Air Filter, on page 442

Cisco ONS 15454 Hardware Installation Guide

444

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G263 Replace the Air Filter of the AC Power Module in the ONS 15454 M6 Shelf Assembly

Summary of Contents for ONS 15454




































































































































































































































































































































































































































































































































Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands

Cisco ONS 15454, Hardware Installation Manual

Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands