Cisco ONS 15454 Hardware Installation Manual Download

Page: 500 / 516

System Power

The ONS 15454 ANSI has these power specifications:

• Nominal Input Voltage: –48 VDC
• Power consumption: Configuration dependent; 55 W (fan tray only)
• Power requirements:

• Nominal: –48 VDC
• Input Voltage Range: –40.5 to –57.0 VDC

• Power terminals: #6 Lug
• ANSI shelf fusing: 100–A fuse panel (minimum 30 A fuse per shelf)HD shelf fusing: 100–A fuse panel

(minimum 30 A fuse per shelf)

The ONS 15454 ETSI has these power specifications:

• Nominal Input Voltage: –48 VDC
• Power consumption: Configuration dependent; 53 W (fan tray only)
• Power requirements:

• Nominal: –48 VDC
• Input Voltage Range: –40.5 to –57.0 VDC

• Power terminals: 3WK3 Combo-D power cable connector (MIC-A/P and MIC-C/T/P faceplates)
• Fusing: 100 A fuse panel; minimum 30 A fuse per shelf

Fan Tray

The following table lists power requirements for the fan-tray assembly.

Table 44: Fan Tray Assembly Power Requirements

BTU/Hr

Amps

Watts

Fan Tray Assembly

198

1.21

FTA2

295

1.8

86.4

FTA3 -T

393

2.4

115

15454E-CC-FTA/15454-CC-FTA

System Environmental Specifications

The ONS 15454 ANSI has these environmental specifications:

• Operating temperature:

C-Temp: 32 to +131 degrees Farenheit (0 to +55 degrees Celsius)

I-Temp: –40 to +139 degrees Farenheit (–40 to +65 degrees Celsius)

• Operating humidity: 5 to 95 percent, noncondensing

The ONS 15454 ETSI has the following environmental specifications:

Cisco ONS 15454 Hardware Installation Guide

470

Hardware Specifications

System Power

Summary of Contents for ONS 15454




































































































































































































































































































































































































































































































































Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands

Cisco ONS 15454, Hardware Installation Manual

Search results

Summary of Contents for ONS 15454

Reviews:

Related manuals for ONS 15454

Brands by name

Popular brands