Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 69 / 516

background image

Step 4

Lift the shelf to the desired position in the rack.

Step 5

Align the screw holes on the mounting brackets with the mounting holes in the rack.

Step 6

Have one person hold the shelf in place while the other person uses the Phillips Dynamometric screwdriver
to install one mounting screw in each side of the assembly.

Step 7

When the shelf is secured to the rack, install the remaining mounting screws.

Use at least one set of the horizontal screw slots on the shelf to prevent slippage.

Note

Step 8

Use the hex tool to remove the temporary set screws.

Step 9

Return to your originating procedure (NTP).

DLP-G680 Mount Multiple ONS 15454 Shelf Assemblies in a Rack

This task installs multiple shelves in a rack.

Purpose

Pinned hex key

#2 Phillips Dynamometric screwdriver

ETSI only:

Two M6 x 20 socket set screws (per shelf)

Eight M6 x 20 pan-head Phillips mounting screws (per shelf)

ANSI only:

Two #12-24 x 3/4 set screws (48-1003-XX) (per shelf)

Eight #12-24 x 3/4 pan-head Phillips mounting screws (48-1004-XX, 48-1007-XX)
(per shelf)

Tools/Equipment

NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454
M6 Shelves, on page 20

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

A standard ETSI rack can hold three ONS 15454 ETSI shelf assemblies and two air ramps. When mounting
a shelf in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the
bottom of the rack. If the rack is provided with stabilizing devices, install the stabilizers before mounting or
servicing the unit in the rack.

Note

Cisco ONS 15454 Hardware Installation Guide

39

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

DLP-G680 Mount Multiple ONS 15454 Shelf Assemblies in a Rack

«
...
67
68
69
70
71
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

ETERNUS HX2000 Series

Brand: Fujitsu Pages: 55

Brand: Fujitsu Pages: 216

Brand: Fujitsu Pages: 374

ONErack 1RK-5RU-KIT

Brand: Tvone Pages: 8

Brand: OSS Pages: 59

Brand: IEI Technology Pages: 9

Brand: Paradyne Pages: 182

Brand: National Instruments Pages: 9

Brand: National Instruments Pages: 7

Case Storage Series

Brand: SilverStone Pages: 28

Brand: National Instruments Pages: 64

Brand: Reely Pages: 108

Sivoia QS roller 100

Brand: Lutron Electronics Pages: 24

Brand: ETAS Pages: 30

Brand: CTC Union Pages: 20

Brand: ADC Pages: 34

Brand: Ariesys Pages: 8

Brand: Ariesys Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands