Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 73 / 516

background image

Procedure

Step 1

The air ramp requires 50 mm of space in a standard 19-inch (482.6-mm) or 23-inch (584.2-mm) rack. Locate
the rack mount unit (RMU) space specified in your site plan.

Step 2

Verify the rack type of your air ramp installation. The brackets are compatible with the following racks.

• 19-inch racks as defined in IEC 297-1(2 Nos.)
• 19-inch for deep door configuration (2 Nos.)
• 23-inch for deep door configuration (2 Nos.)
• Pan Head M4x 8mm (4 Nos.)
• Air Filter

Step 3

Verify that the mounting brackets attached to the unit are correct for your rack size. Complete the

Reverse the Mounting Bracket to Fit a 19-inch (482.6-mm) Rack (ANSI Only), on page 33

as required.

Step 4

Align the chassis with the rack mounting screw holes; insert and tighten the four screws.

In an ETSI configuration the air ramp comes with pre-installed brackets as illustrated in the following figure.

Figure 17: Air Ramp with Brackets in an ETSI Configuration

Step 5

To install the 19-inch and 23-inch brackets on an ONS 15454 ANSI, with standard door and spool, remove
the screws that attach the mounting bracket to the side of the shelf.

Step 6

Align the mounting bracket screw holes against the shelf screw holes according to the following figure.

Cisco ONS 15454 Hardware Installation Guide

43

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

DLP-G8 Install the Air Ramp

«
...
71
72
73
74
75
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

CoreBuilder 9000

Brand: 3Com Pages: 12

CoreBuilder 9000

Brand: 3Com Pages: 8

Brand: IEI Technology Pages: 10

Brand: ERECA Pages: 19

Brand: Raisecom Pages: 84

Brand: IBM Pages: 44

Brand: Apevia Pages: 11

Brand: Otto Bock Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands