Cisco ONS 15454 Hardware Installation Manual Download | Manualshive

Page: 96 / 516

background image

NTP-G6 Install the MIC-A/P and MIC-T/C/P FMECs (ETSI Only)

This procedure installs the MIC-A/P and the MIC-T/C/P FMECs in the EFCA.
The EFCA is located at the top of the ONS 15454 ETSI shelf. It provides
connection for installing power, external alarms, timing input and output, and
craft interface terminals.

Purpose

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

FMECs (the MIC-A/P and MIC-T/C/P)

Tools/Equipment

NTP-G4 Open and Remove the FMEC Cover (ETSI Only), on page 60

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Voltage is present on the backplane when the system is operating. To reduce risk of an electric shock,
keep hands and fingers out of the power supply bays and backplane areas.

Statement 166

Warning

Always use the supplied ESD wristband when working with a powered ONS 15454 ETSI. For detailed
instructions on how to wear the ESD wristband, refer to the

Electrostatic Discharge and Grounding Guide for

Cisco CPT and Cisco ONS Platforms

.

Caution

The ONS 15454 ETSI EFCA has 12 FMEC slots numbered sequentially from left to right beginning with Slot
18. Slots 18 to 22 and 25 to 29 provide electrical connections for the corresponding slots, so they are
unnecessary in DWDM applications.

Note

Procedure

Step 1

Ensure that you are installing the FMECs in the correct slot:

• FMEC Slot 23 supports the MIC-A/P.

The MIC-A/P card provides connection for the BATTERY B input, one of the two possible redundant power
supply inputs. It also provides connection for eight alarm outputs (coming from the TCC2/TCC2P/TCC3
card), sixteen alarm inputs, and four configurable alarm inputs/outputs.

• FMEC Slot 24 supports the MIC-C/T/P.

Cisco ONS 15454 Hardware Installation Guide

66

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

NTP-G6 Install the MIC-A/P and MIC-T/C/P FMECs (ETSI Only)

«
...
94
95
96
97
98
...
»

Summary of Contents for ONS 15454





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454

Brand: LG Pages: 16

Brand: Comet Models Pages: 2

Brand: F5 Pages: 11

Racal Instruments 1264C

Brand: Eads Pages: 100

PXI Express PXIe-1066DC

Brand: National Instruments Pages: 79

Brand: IEI Technology Pages: 8

Brand: Fujitsu Pages: 12

Brand: Fujitsu Pages: 29

Brand: Xena Networks Pages: 16

Brand: Sliger Pages: 16

Brand: Georgia Institute of Technology Pages: 92

Brand: CSN Pages: 2

Brand: ASROCK Pages: 1

FortiGate FortiGate-5020

Brand: Fortinet Pages: 64

Brand: Hypercom Pages: 198

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands